background image

Ready Light 

The ready light is “on” when the system is ready to arm and “flashes” if ready to 
force arm. The ready light is off when the system is not ready to arm because 
of a zone(s) being faulted. 

Stay Light 

The  stay light is “on” when the all interior (motion detector) zones are 
bypassed. 

Zone Light  

The zone lights are “off” when everything is normal. A zone light will be “on” if 
the zone has been bypassed. If a zone light is “flashing”, that zone is in alarm 
or has been faulted. If a zone light is “flashing” rapidly, it means that the zone is 
in a trouble condition.   Trouble conditions are: 

 

Tamper 

 

Hardware 

 

Low Battery 

 

Loss of Supervision 

(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid 
“flashing” light for a short period of time, followed by a slow “flashing” light.) 

 
 

EMERGENCY ACTIVATION KEYS 

 
 

NOTES: You must hold these keys for 2 seconds to activate these 
functions.   Your system may not be programmed for these activation keys 
(see page 1)
.  You should press these keys only in an emergency situation that 
requires response by emergency personnel.   If your system is programmed for 
these functions, the following reports can be sent. 
 
Fire Key
 – This key can activate the fire alarm when pressed for two seconds. If 
your system is connected to a monitoring center, an emergency report could be 
sent to that center. 
 
Auxiliary Emergency Key
 – This key can activate the auxiliary alarm when 
pressed for two seconds. If your system is connected to a monitoring center, an 
emergency report could be sent to that center.  
 
Police (Panic/Hold-Up) Key
 - This key can sound a local audible alarm when 
pressed for two seconds. If your system is connected to a monitoring center, an 
emergency report could be transmitted to that center.  NOTE: Some Panic/Hold-
Up alarms are programmed to be silent at the protected site while reporting an 
alarm to the monitoring center. Check with your installing company to determine 
how your security system will respond to the Panic/Hold-Up activation. 

Summary of Contents for NetworX NX-8E





















Reviews: