background image

 

 

Connecting a Camera 

Note: The unit can be placed horizontally or vertically.  If it is placed 
vertically, the modem side must face up. 

 

Figure 6 - Attaching the Unit 

Modem 

Side support

Anchoring 

surface

3.

 

Connect the system to the vehicle battery using the PowerIn connector 

(see 

Figure 1

, page 1): 

 

Connect the red wire to the positive (+) connector 

 

Connect the black wire to the negative (-) connector 

 

Connect wire to the car ignition 

Note: For additional information, see “

Power Connection and Usage

,” 

page 2. 

4.

 

Insert a cellular modem in one of the PCMCIA slots in the modem 

compartment (see 

Figure 1

, page 1).  

Note: Either the upper or lower slot can be used. 

* Important note:

 Do not power off the system without supplying a 

signal that informs about it (e.g. switching off the ignition) 

Connecting a Camera 

Up to four cameras can be connected to the IVG-400.  To connect a camera to 

the unit: 

1.

 

Install the camera in its desired location in the vehicle. 

2.

 

Connect the video output of the camera to a VideoIn connector on the 
rear panel of the IVG-400 (see 

Figure 1

, page 1). 

3.

 

Optional: If the camera has remote control features (pan, tilt, and/or 
zoom), these can be activated by connecting the camera controller to an 

RS232/485 connector on the rear panel of the IVG-400 (see 

Figure 1

page 1) using a D-type 9-pin female connector (

Figure 2

, page 1). 

Connecting a Sensor 

Up to six input sensors can be connected to the IVG-400.  To connect a sensor to 
the unit: 

1.

 

Install the sensor in its desired location in the vehicle. 

 

IVG-400 Installation Instructions 

 

 

 

Page 4 of 7 

 

Summary of Contents for MVS-44










Reviews: