background image

 

 

Selecting a Location 

The following additional hardware is required to install the IVG-400 and connect 
cameras to it: 

1.

 

Screws to connect the unit to its anchoring surface 

2.

 

Cellular modem 

3.

 

16 AWG red and black cable to connect the unit to the vehicle battery 

4.

 

Coax cable to connect the camera to the IVG-400 

Additional hardware is required for the following 
optional features:  

 

IVG-400 Installation Instructions 

 

 

 

Page 2 of 7 

he 

1.

 

Camera control: 

 

Flat ribbon cable with D-type 9-pin 
female connector (Pin 6-TX positive, 

Pin 7-TX negative) 

Figure 2 - Flat ribbon 

cable with D-type 9-pin 
female connector 

2.

 

Connecting a sensor: 

 

Two wires to connect the output to t
IVG-400 dry contacts (normally 

included with the sensor) 

3.

 

Connecting an alarm: 

 

16 AWG red and black cable to connect the 
alarm to the IVG-400, and, for release 1, 
to a relay 

 

For release 1: A 12VDC power relay, such 
as the Fujitsu FTR-MYAA012A   

 

Figure 3 – Fujitsu FTR-

MYAA012A relay 

Selecting a Location 

IVG-400 should be placed in the coolest available location in the driver’s cabin of 

the vehicle.  Some options are: 

 

Under a seat 

 

Immediately below the ceiling 

 

Beside the driver’s seat, under the window 

Power Connection and Usage 

The IVG-400 draws its power from the vehicle battery.  Its current consumption 
is 1.5AMP at 12V DC or 0.75AMP at 24V DC.  
The IVG-400 can be connected to the vehicle battery in one of two ways: 

 

Directly 

 

Through the ignition switch 

 

Summary of Contents for MVS-44










Reviews: