manualshive.com logo in svg

GE MultiLink ML1200, Instruction Manual

Share
Download
GE MultiLink ML1200 Instruction Manual Download Page 62

4–4

MULTILINK ML1200 MANAGED FIELD SWITCH – INSTRUCTION MANUAL

OPERATION

CHAPTER 4: OPERATION

4.1.5

Power Budget Calculations for ML1200 PM’s with Fiber Media

Receiver Sensitivity and Transmitter Power are the parameters necessary to compute the 
power budget. To calculate the power budget of different fiber media installations using 
Multilink products, the following equations should be used:

OPB (Optical Power Budget) = P

T

(min) - P

R

(min)

where P

T 

= Transmitter Output Power, and P

R

 = Receiver Sensitivity

Worst case OPB = OPB - 1dB(for LED aging) - 1dB(for insertion loss)

Worst case distance = {Worst case OPB, in dB} / [Cable Loss, in dB/Km]

where the “Cable Loss” for 62.5/125 and 50/125

μ

m (M.m) is 2.8 dB/km, 

and the “Cable Loss” for 100/140 (Multi-mode) is 3.3 dB/km,

and the “Cable Loss” for 9/125 (Single-mode) is 0.5 dB/km

and the “Cable Loss” for 9/125 (Single-mode) is 0.4 dB/km (LX25)

and the “Cable Loss” for 9/125 (Single-mode) is 0.25 dB/km (ZX40)

and the “Cable Loss” for 9/125 (Single-mode) is 0.2 dB/km (ZX70)

The following data has been collected from component manufacturer’s (Agilent’s and 
Lucent’s) web sites and catalogs to provide guidance to network designers and installers.

Fiber Port 

Module

Speed, Std.

Mode

Std. km 

fdx

(hdx)

Wavelength

nm

Cable Size/

μ

m X’mitr 

Output

P

T

dB

R’cvr 

Sens.

P

R

dB

Worst 

OPB,

dB

Worst* 

distance 

Km

fdx

typical

OPB,

dB

typical*

distance

Km

fdx 

C7

10Mb

FL

Multi-Mode 2

(2)

850

62.5/125

100/140

50/125

-15.0

-9.5

-19.5

-31

-31

-31

14

19.5

19.5

5

5.9

3.4

17

23.5

13.5

6 

7

4.8

C8, C9

100Mb

FX

Multi-mode 2

(0.4)

1300

62.5/125

50/125

-20

-23.5

-31

-31

9.0

5.5

3.0

2.0

14

12

5

4

CA

100Mb

FX

Single-mode 18+

(0.4)

1300

9/125

-15

-31 14

28

17.5 35

CB

100Mb

FX

Single-mode 40

(0.4)

1300

9/125

-5

-34 29

58

32.5 65

CC

100Mb

FX

Multi-mode 2

(0.4)

1300

62.5/125

50/125

-20

-23.5

-31

-31

9.0

5.5

3.0

2.0

15.8

12.2

5.5

4.0

CD

100Mb

FX

Multi-mode 2

(0.4)

1300

62.5/125

-19

-31 12

4

16

5.7

CE

100Mb

FX

Single-Mode 15+

(0.4)

1310

9/125

-15

-28 11

22

-

-

H3, HG

1000 Mb FX

(Gigabit)

Single-Mode 10

1310

9/125

-10.0 -22 10

22

11

24

Summary of Contents for MultiLink ML1200

























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands