GE Monogram ZVC30LSS, Installation Instructions Manual, Page: 2 / 24

2
Installation Instructions
WARNING:
TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag,
to the service panel.
AVERTISSEMENT :
POUR RÉDUIRE LE RISQUE D’INCENDIE,
DE CHOC ÉLECTRIQUE OU DE BLESSURES
CORPORELLES, IL FAUT OBSERVER LES REGLES SUIVANTES :
A.
Utilisez cet appareil uniquement de la manière prévue
par le fabricant. En cas de question, consultez le fabricant.
B. Avant tout entretien, réparation ou nettoyage, coupez
l’alimentation électrique au disjoncteur et verrouillez le
panneau du disjoncteur pour éviter la mise sous tension
accidentelle. S’il est impossible de verrouiller le panneau
du disjoncteur, attachez solidement une note de mise en
garde très visible, comme une étiquette, au panneau.
CAUTION:
For General Ventilating Use
Only. Do Not Use To Exhaust Hazardous Or
Explosive Materials And Vapors.
ATTENTION :
Utilisez uniquement
pour une ventilation générale. N’utilisez pas pour
évacuer des vapeurs ou des matériaux
dangereux ou explosifs.
WARNING:
TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
C. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the outdoors.
• Local codes vary. Installation of electrical connections
and grounding must comply with applicable codes. In
the absence of local codes, the vent should be installed
in accordance with National Electrical Code ANSI/NFPA
70-1990 or latest edition.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
•IMPORTANT
–
Save these instructions for local
inspector’s use.
•IMPORTANT
–
Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill Level – Installation of this vent hood requires
basic mechanical and electrical skills.
• Completion time – 1 to 3 hours.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram service in Canada, call 1.888.880.3030.
For Monogram Parts and Accessories, call
1.800.626.2002.
CAUTION:
Due to the weight and size of these vent
hoods and to reduce the risk of personal
injury or damage to the product, TWO PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
ATTENTION :
À cause du poids et des dimensions du
ces hottes et pour réduire les risques de
blessures ou de dommages du produit, IL FAUT
DEUX PERSONNES POUR FAIRE UNE INSTALLATION
CORRECTE.
WARNING:
To reduce the risk of fire or electrical shock,
do not use this range hood with any external
solid-state speed control device. Any such alteration
from original factory wiring could result in damage to
the unit and/or create an electrical safety hazard.
AVERTISSEMENT :
Pour réduire le risque d’incendie ou de
choc électrique, il ne faut pas utiliser cette
hotte avec un régulateur de vitesse électronique
externe. Toute modification de ce type du branchement
d’usine peute endommager l’appareil ou créer un risque
de choc électrique.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCTWORK.