GE Monogram ZBD1800K Series Technical Service Manual Download Page 29 | Manualshive

Page: 29 / 46

background image

– 29 –

Troubleshooting

WARNING: Always turn off the electric power
supply before servicing any electrical component,
making ohmmeter checks, or replacing any parts.

Note: All voltage checks should be made with a
voltmeter having a full-scale range of 130 volts or
higher. After service is completed, be sure all
safety grounding circuits are complete, all
electrical connections are secure, and all access
panels are in place.

Troubleshooting the Door Switch

The door switch can be tested using an
ohmmeter and the strip circuit.

1. Disconnect the electric supply from the

dishwasher.

2. Remove the wire leads from the door switch.

3. Use an ohmmeter to check the door switch for

continuity.

4. If the door switch is defective, remove it from

the latch assembly. If the door switch is good,
check to see if the timer is defective.

Door Switch Strip Circuit

SWITCH

PRESSURE

OPTIONAL

SWITCH

«
...
27
28
29
30
31
...
»

Summary of Contents for Monogram ZBD1800K Series















































Reviews:

No comments

Related manuals for Monogram ZBD1800K Series

Brand: Clatronic Pages: 42

Brand: Viking Pages: 12

Brand: Gaggenau Pages: 64

Brand: Magic Chef Pages: 32

Brand: OZTI Pages: 24

Brand: Hotpoint Pages: 12

Brand: Insinger Pages: 2

Brand: Swiss Pages: 26

Brand: GE Pages: 28

Brand: Malber Pages: 19

Brand: Electrolux Pages: 44

Brand: Electrolux Pages: 40

OKO Lavamat 605 electronic

Brand: AEG Pages: 32

Brand: Tricity Bendix Pages: 28

Brand: Miele Pages: 112

Brand: Miele Pages: 36

WSD 323 Selection

Brand: Miele Pages: 84

WS 5425 MC 7 Professional

Brand: Miele Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands