background image

Part No. 245B1790P064 (2)
Pub. No. 31-1163 (2)

(N.D. 558) 7/02

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Screw D

Step 7
Installing the Trim Kit Frame

1. Using the assembled Trim Kit Frame as a
template (and with the microwave oven in
position and secured), insert the Trim Kit
Frame into the cutout and locate the
attaching holes. Temporarily hold the
Trim Kit Frame in place by starting the
four screws that attach the trim kit frame
to the Base Pan and Side Covers. Push the
Trim Kit Frame as far to the left as possible
driving the four inside screws into Base
Pan and Side Cover. Be sure the door
clears the trim when open. 

Mark the four

holes on the side trim.

2. Remove the Trim Kit Frame.

3. Center punch and drill 3/32" dia. pilot
holes per their hole center marks for the
mounting screws.

4. Position the assembled Trim Kit Frame
around the Oven and secure it with 8
screws (C). Use the smaller Phillips head
screwdriver (#1) to prevent burring the
Phillips head.

CAUTION: 

Do not overtighten screws

since it can cause misalignment of top/
side strips.

Trim Kit Frame

Wall Installation

Mark

Mark

Mark

Mark

Screw C

Screw D

Screw D

Screw D

Screw D

Bottom Trim (5)

Top Trim (4)

Side

Trim

(6)

Side Trim (6)

Step 6
Assembling the Trim Kit Frame

Assemble Top Trim (4), Bottom Trim  (5)
and Side Trims (6) shown with the #6 x
1/2"L flat head thread-forming screws
(D). Fasten through holes in the Trim Kit
Sides (6) as shown.

CAUTION: 

After assembly, top, bottom

and side strips must be flush.

Note: 

Bottom Trim (5) has a hinge

notch and is not interchangeable
with Top Trim (4).

Summary of Contents for JX827SS

Page 1: ...pable of supporting a minimum of 100 lbs Screw E Screw D 1 Parts Inventory B 2 4 5 6 C A E D 7 3 3 Screw C Screw A Screw B CAUTION Before you begin Read these instructions Owner s Manual and Important Safety Instructions completely and carefully This Kit is for use on models JEM21K L JEM23K L JEM25L GN GV GY WN WV WY BF WF JES833WY JEM825K JEM27KWH LWH JEM31L M GN GV GY WV WY GA WA CA BF CF WF SF ...

Page 2: ...an front flange as your guide center the drill in the base holes keeping the front flange centered and tight against the cabinet front wall Slide the two Rear Holddown Brackets 7 from the rear into the slots in the Base Pan The tongues of the Rear Holddown Brackets should be sticking into the base be centered in the slot and be into the slot as far as it will go Mark and drill four 3 32 diameter h...

Page 3: ...ition on the right side Drive one screw A through the rear duct into the partition in the Base Pan Drive one screw A into the rear duct side flange near the lamp cover Drive three screws through the Base Pan into the rear duct bottom Replace the screw removed from the top left to complete the rear duct installation The Base Pan should be completely sealed to the microwave oven in the back and all ...

Page 4: ...ove the Trim Kit Frame 3 Center punch and drill 3 32 dia pilot holes per their hole center marks for the mounting screws 4 Position the assembled Trim Kit Frame around the Oven and secure it with 8 screws C Use the smaller Phillips head screwdriver 1 to prevent burring the Phillips head CAUTION Do not overtighten screws since it can cause misalignment of top side strips Trim Kit Frame Wall Install...

Reviews: