background image

Tools Needed

2 Phillips head screwdrivers (#1 & #2)
Drill and 3/32" drill bit
Centerpunch or nail
Pencil and ruler
Knife

Installation Procedure

Step 2
Installation of Base Pan

Disconnect microwave oven from recep-
tacle. Remove everything out of the
microwave oven (packing, glass shelf,
temperature probe, Use & Care books).
Remove the four top plug buttons from
the top of the Microwave Oven cabinet.
Use knife to pry up plug buttons using
care not to scratch the microwave oven.
A clear protective film has been applied to
some microwave oven cabinets. If applied,
remove the film. Place the microwave
oven on the base pan
(1) centered left to right.

V Notch

Remove 4 Plug Buttons

120V/60 Hertz
Grounded Power 
Outlet

V Notch

Screw C

Drive two Screws
(C) into the Base
Pan front flange to
hold in place
temporarily.

using the two holes in the Base Pan front flange as your guide
(center the drill in the base holes keeping the front flange
centered and tight against the cabinet front wall).

Slide the two Rear Holddown Brackets (7) from the rear into
the slots in the Base Pan. The tongues of the Rear Holddown
Brackets should be sticking into the base, be centered in the slot,
and be into the slot as far as it will go. Mark and drill four 3/32"
diameter holes. Mount the Rear Holddown Brackets using four
Screws (B). Both Rear Holddown Bracket tongues should now be
centered in the slotted holes in the base and be into the base as
far as they can go.

Remove the two screws in the Base Pan front flange and slide the
Base Pan straight out.

Screw B

Step 1
Locating and Installing Rear

Holddown Supports

Set Base Pan (1) into the front cabinet
microwave oven cutout and center it right
and left. Push back until front flange is
against cabinet front wall. Use the V-notch
in the Base Pan front flange to center the
Base Pan. Bore two 3/32" diameter holes
into the wooden cabinet base front edge

Summary of Contents for JX827SS

Page 1: ...pable of supporting a minimum of 100 lbs Screw E Screw D 1 Parts Inventory B 2 4 5 6 C A E D 7 3 3 Screw C Screw A Screw B CAUTION Before you begin Read these instructions Owner s Manual and Important Safety Instructions completely and carefully This Kit is for use on models JEM21K L JEM23K L JEM25L GN GV GY WN WV WY BF WF JES833WY JEM825K JEM27KWH LWH JEM31L M GN GV GY WV WY GA WA CA BF CF WF SF ...

Page 2: ...an front flange as your guide center the drill in the base holes keeping the front flange centered and tight against the cabinet front wall Slide the two Rear Holddown Brackets 7 from the rear into the slots in the Base Pan The tongues of the Rear Holddown Brackets should be sticking into the base be centered in the slot and be into the slot as far as it will go Mark and drill four 3 32 diameter h...

Page 3: ...ition on the right side Drive one screw A through the rear duct into the partition in the Base Pan Drive one screw A into the rear duct side flange near the lamp cover Drive three screws through the Base Pan into the rear duct bottom Replace the screw removed from the top left to complete the rear duct installation The Base Pan should be completely sealed to the microwave oven in the back and all ...

Page 4: ...ove the Trim Kit Frame 3 Center punch and drill 3 32 dia pilot holes per their hole center marks for the mounting screws 4 Position the assembled Trim Kit Frame around the Oven and secure it with 8 screws C Use the smaller Phillips head screwdriver 1 to prevent burring the Phillips head CAUTION Do not overtighten screws since it can cause misalignment of top side strips Trim Kit Frame Wall Install...

Reviews: