29
Car
e and Cleaning
29
Cleaning the Radiant Module (continued)
Burned-On Residue
WARNING: DAMAGE to your glass surface may
occur if you use scrub pads other than BLUE
Scotch-Brite
®
Multi-Purpose No Scratch scrub
pads by 3M.
1. Allow the radiant
module to cool.
2. Spread a few drops
of Cerama Bryte
®
to
the entire burned
residue area.
3. Using the Scotch-Brite
®
blue pad, rub the
residue area, applying
pressure as needed.
4. If any residue remains, repeat the steps listed above
as needed.
5. For additional protection, after all residue has been
removed, polish the entire surface with Cerama
Bryte
®
and a paper towel.
Heavy, Burned-On Residue
1. Allow the radiant
module to cool.
2. Spread a few drops of
Cerama Bryte
®
to the
entire burned residue
area.
3. Hold the razor scraper
at approximately a 45°
angle against the glass
surface and scrape the
soil. It will be necessary
to apply pressure to the
razor scraper in order to
remove the residue.
4. Keep a small amount of
cream on the residue as
you scrape.
5. After scraping with the razor scraper, use the
Scotch-Brite
®
blue pad to remove any remaining
residue.
6. For additional protection, after all residue has been
removed, polish the entire surface with Cerama
Bryte
®
and a paper towel.
Metal Marks and Scratches
1. Be careful not to slide pots and pans across your
radiant module. It will leave metal markings on
the surface.
These marks are removable using the cleaning
cream with a Scotch-Brite
®
blue pad and/or
razor scraper.
2. If pots with a thin overlay of aluminum or copper
are allowed to boil dry, the overlay may leave
black discoloration on the surface.
This should be removed immediately before
heating again or the discoloration may
be permanent.
WARNING: Carefully check the bottom of
pans for roughness that would scratch the
radiant module.
Glass Surface – Potential for
Permanent Damage
Our testing shows that if you are cooking high sugar
mixtures such as jelly or fudge and have a spillover,
it can cause permanent damage to the glass surface
unless the spillover is immediately removed.
Damage from Sugary Spills and Melted Plastic
1. Turn off all surface units. Remove hot pans.
2. Wearing an oven mitt:
a. Use the razor scraper to move the spill to a cool
area on the radiant module.
b. Remove the spill with paper towels.
3. Any remaining spillover should be left until the
surface has cooled.
4. Don’t use the radiant module again until all of the
residue has been completely removed.
NOTE: If pitting or indentation in the glass
surface has already occurred, the radiant module
glass will have to be replaced. In this case, service
will be necessary.
To Order Parts
To order Cerama Bryte
®
and the razor scraper, please
call our toll-free number:
National Parts Center
800.626.2002.
Cerama Bryte
®
Cream
. . . . . . .
# WX10X300
Razor Scraper
. . . . . . . . . . . . . .
# WX5X1614
Kit
. . . . . . . . . . . . . . . . . . . . . . . . . .
# WB64X5027
(Kit includes cream and razor scraper)
Scotch-Brite
®
Multi-Purpose
No Scratch blue scrub pad
The RAZOR SCRAPER is
available through our Parts
Center. See instructions
under “To Order Parts”
section at right.
NOTE: Razor blade is
packed inverted for safety
reasons. Prior to use, the
blade must be rotated and
reinserted into slot. Do not
use a dull or nicked blade.
ge.com
