manualshive.com logo in svg

GE JGSP48, Installation Instructions Manual, Page: 14 / 16

Share
Download
GE JGSP48 Installation Instructions Manual Download Page 14

14

Installation Instructions

INSTALL THE RANGE 

(CONT.)

BAKE AND BROIL BURNERS

If the bake and/or broil burners have lifting or
“lazy” (floating) flames or you have a yellow
flame, perform the following procedures:

CHECKING THE OVEN BURNERS

To check the bake burner flames with the
oven door in the closed position:

1.

Open the door and remove it.

2.

Remove the oven racks.

3.

Remove the oven bottom.
Lift the oven bottom up at rear and pull
forward.

4.

Remove the four screws holding the burner
baffle (flame spreader) to the burner box.

5.

Install and close the oven door.

6.

Turn on the bake burner.

As you watch the flames, check the
following:

• 

Burner flames should not flutter or blow
away from the burner.

• 

They should be blue in color with no trace
of yellow.

The broil burner flames may be seen without
removing the racks, oven bottom or bake
baffles.

A

18

ADJUST THE AIR SHUTTER

BAKE BURNER

1.

Remove the orifice fitting cover.

2.

Use a screwdriver to loosen the air shutter

screw.

3.

Adjust the air shutter to 11/32

″

.

4.

Retighten the air shutter screw.

WHAT ADJUSTMENT TO MAKE:

a.

If the flames are yellow, open the air
shutter more than the original setting.

b.

If the flames blow away or fluttered from
the burner, close the air shutter more than
the original setting.

Burners should be checked frequently.

BROIL BURNER

1.

The broil burner is located and accessible
in the top rear of the oven.

2.

Using a

screwdriver,
loosen the air
shutter
adjustment screw. 

3.

Make the air
shutter
adjustment.

4.

Retighten the air
shutter screw.

5.

Check the inner
cone of the flame.
It should be
between 1/2

″

and

3/4

″

long for the

oven bake and
broil burners.

WHEN ALL ADJUSTMENTS ARE MADE AND
THE RESULTS ARE SATISFACTORY

1.

Replace the orifice fitting cover.

2.

Replace the burner baffle (flame spreader)

and screws.

3.

Replace the oven bottom.

4.

Replace the oven door.

B

Air Shutter 

Adjustment Screw

Dim. “A”

1/2" TO 3/4"

CONO INTERIOR 
        DE LLAMA

QUEMADOR PARA
HORNEAR/ASAR

Inner cone of
flame

Oven broiler
burner

1/2

″

to 3/4

″

Air shutter
adjustment screw

Dim. “A”

Orifice fitting

cover

Air shutter

Air shutter
screw

Summary of Contents for JGSP48

















Reviews:

No comments