background image

Burned-On Residue

WARNING: 

DAMAGE to your glass surface

may occur if you use scrub pads other than 
the pad included with your cooktop.

Allow the cooktop to cool.

Remove the burner grates, vent
grille and vent grille gasket.
Spread a few drops of CERAMA
BRYTE

®

Ceramic Cooktop Cleaner

to the entire burned residue area.

Using the included CERAMA
BRYTE

®

Cleaning Pad for Ceramic

Cooktops, rub the residue area,
applying pressure as needed.

If any residue remains, repeat the
steps listed above as needed.

For additional protection, after all
residue has been removed, polish
the entire surface with CERAMA
BRYTE

®

Ceramic Cooktop Cleaner

and a paper towel.

Use a CERAMA BRYTE

®

Cleaning

Pad for Ceramic Cooktops or a
Scotch-Brite

®

Multi-Purpose No

Scratch blue scrub pad.

The control knobs may be removed for easier
cleaning.

Make sure the knobs are in the 

OFF

positions and pull them straight off the
stems for cleaning.

The knobs can be cleaned in a
dishwasher or they may also be washed
with soap and water. Make sure the
insides of the knobs are dry before
replacing.

Replace the knobs in the 

OFF

position 

to ensure proper placement.

13

Safety Instructions

Operating Instructions

Care and Cleaning

Tr

oubleshooting T

ips

Consumer Support

Control Knobs

Flat

Molded flat area

The control knobs may be removed
for easier cleaning.

ge.com

Normal Daily Use Cleaning

ONLY 

use CERAMA BRYTE

®

Ceramic

Cooktop Cleaner on the glass cooktop.
Other creams may not be as effective.

To maintain and protect the surface of
your glass cooktop, follow these steps:

Before using the cooktop for the 
first time, clean it with CERAMA
BRYTE

®

Ceramic Cooktop Cleaner.

This helps protect the top and
makes clean-up easier.

Daily use of CERAMA BRYTE

®

Ceramic Cooktop Cleaner will help
keep the cooktop looking new.

Remove the burner grates, vent
grille and vent grille gasket.

Shake the cleaning cream well.
Apply a few drops of CERAMA
BRYTE

®

Ceramic Cooktop Cleaner

directly to the cooktop.

Use a paper towel or CERAMA
BRYTE

®

Cleaning Pad for Ceramic

Cooktops to clean the entire
cooktop surface.

Use a dry cloth or paper towel 
to remove all cleaning residue. 
No need to rinse.

NOTE: 

It is very important that you DO NOT

heat the cooktop until it has been cleaned
thoroughly.

Clean your cooktop after

each spill. Use CERAMA

BRYTE

®

Ceramic Cooktop

Cleaner.

Cleaning the glass cooktop.

Summary of Contents for JGP989









































































Reviews: