background image

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by

individuals possessing adequate backgrounds of electrical,
electronic, and mechanical experience. Any attempt to repair a
major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible for the
interpretation of this information, nor can it assume any liability in
connection with its use.

WARNING

If the information in this manual is not followed exactly, a fire or

explosion may result causing property damage, personal injury or
death. If you smell gas:

-

Do not try to light any appliance.

-

Do not touch any electrical switch; do not use any phone in
the building.

-

Immediately call the gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.

-

If you cannot reach the gas supplier, call the fire department.

CAUTION

To avoid personal injury, disconnect power before servicing this

product. If electrical power is required for diagnosis or test
purposes, disconnect the power immediately after performing the
necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used

to complete a path to ground are removed for service, they must
be returned to their original position and properly fastened.

GE Consumer Service Training

Technical Service Guide

Copyright © 2000

All rights reserved. This service guide may not be reproduced in whole or in part
in any form without written permission from the General Electric Company.

!

Summary of Contents for JGB910 and































Reviews: