background image

26

Consumer Product Ownership Registration

Model Number

Serial Number

Important

Mail 

Today!

GE Appliances

General Electric Company
Louisville, Kentucky 40225

First

Name

Mr. 

Ms. 

Mrs. 

Miss 

Street

Address

City

State

Date Placed

In Use

Month

Day

Year

Zip

Code

Apt. #

Last

Name

Phone

Number

_

_

Consumer Product Ownership Registration

Dear Customer:
Thank you for purchasing our product and thank you for placing your 
confidence in us. We are proud to have you as a customer!

Follow these three steps to protect your new appliance investment:

Complete and mail
your Consumer
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the unlikely event of
a safety modification.

After mailing 
the registration
below, store this
document in a safe
place. It contains
information you 
will need should
you require service.
Our service number
is 800-GE-CARES 
(800-432-2737).

Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
If you have questions,
or need more
information call the 
GE Answer Center

®

800.626.2000.

Important: 

If you did not get a registration card with your product,

detach and return the form below to ensure that your

product is registered.

1 2 3

Model Number

Serial Number

Cut here

Summary of Contents for GNSF48A01

































Reviews: