background image

13

14

4.3.2 AC Circuit Breaker And Residual Current Device

An independent three or four pole circuit breaker for each inverter must be installed at the output 
side to ensure that the inverter can be securely disconnected from the grid.      

The internal integrated residual current detection device (RCD) of inverter can detect external 
leakage current in real time, when detecting the leakage current value exceeds the limit value, the 
inverter will be disconnected from the grid as soon as possible. If an external RCD is installed , the 
action current should be 500mA or higher.

4.3.3 Earth Terminal Connection

The inverter is equipped with earth terminal according to the requirement of EN 50178.
All non-current carrying exposed metal parts of the equipment and other enclosures in the PV 
power system should be grounded.
Please connect 'PE' cable to ground.
1. Strip the wire insulation sheet of a suitable length with a wire stripper.

Output Current

31.5A

40A

54.5A

40A

43.3A

48A

53.3A

80A
96A
80A
96A

Inverter Model

GEP12-L-10
GEP15-L-10
GEP20-L-10

GEP25-10

GEP29.9-10

 GEP30-10 

GEP36-10

GEP30-L-10
GEP35-L-10

GEP50-10
GEP60-10

Recommended Nominal Current Of AC Breaker

>40A
>50A
>68A
>50A
>55A
>60A
>66A

>100A
>120A
>100A
>120A

L1

L2=L1 + (1~2mm)

2. Insert the stripped wire into the terminal and compress it tightly by crimping pliers.

Step 3: 

From the accessory bag terminal, set on the wire and tool clamping.

Use tool clamp terminals

If use line pressing pliers, wire diameter 
smaller two separating, crimping terminal 
shape rules after no prominent spikes.

Insulation casing spin out completely 
covered terminal wire tube.

Insulation casing set to the 
cable.

Put the cold-press terminal 
received cables.

The final result

The final result

GEP30~35-L-10/GEP50~60-10 models using cold pressed terminals

GEP12~20-L-10/GEP25~36-10 models use terminals

Step 4: 

Use flat head screw driver side screw counterclockwise communication terminals, 

make five interface is open.

Step 6: 

The communication terminal cover closed, using communication connection cap 

screw clockwise twist will exchange cover tighten.(2.3 N.m fastening torque).

Step 5: 

The communication cable line according to the sequence access communication 

terminal station, then twisting the screw clockwise (2.3 N.m fastening torque).

L1

L2

L3

N

PE

It's not allowed for several inverter to use the same circuit breaker. It's not allowed to 
connect loads between inverter and circuit breaker.

Summary of Contents for GEP

























Reviews: