background image

10

49-6000243  Rev. 0

Installation Instructions

ELECTRICAL CONNECTIONS

A separate branch circuit with copper conductors, 

overcurrent protective device and suitable 

disconnecting means must be provided by a qualified 

electrician. 

All wiring must conform to local codes or latest edition 

of National Electrical Code ANSI/NFPA 70.

The voltage requirements and wattage load for the 

water heater are specified on the rating label on the 

front of the water heater.

The branch circuit wiring should include 

either:

1.  Metallic conduit or metallic sheathed cable approved

for use as a grounding conductor and installed with

fittings approved for the purpose.

2.  Nonmetallic sheathed cable, metallic conduit or

metallic sheathed cable not approved for use

as a ground conductor shall include a separate

conductor for grounding. It should be attached to

the ground terminals of the water heater and the

electrical distribution box.

WARNING

 It is recommended for this

product to be installed by a licensed and qualified 

electrician in accordance with all applicable 

national, state, and local electrical codes.
Under no circumstances should you attempt to 

install, repair, or disassemble the water heater 

without first shutting off power directly at the fuse 

or breaker box. 
Before installing this product, make sure the 

installation location has sufficient electrical power 

available to handle the maximum amperage load 

for the water heater.

WARNING

 Proper ground connection is 

essential. The presence of water in the piping 

and water heater does not provide sufficient 

conduction for a ground. Nonmetallic piping, 

dielectric unions, flexible connectors, etc., can 

cause the water heater to be electrically isolated. 

Do not disconnect factory ground.

The manufacturer’s warranty does not cover any 

damage or defect caused by installation, attachment 

or use of any type of energy-saving or other 

unapproved devices (other than those authorized by 

the manufacturer) into, onto or in conjunction with the 

water heater. The use of unauthorized energy-saving 

devices may shorten the life of the water heater and 

may endanger life and property. 
The manufacturer disclaims any responsibility for 

such loss or injury resulting from the use of such 

unauthorized devices.

NOTE:

 do not cover the operating or warning labels attached 

to the water heater or attempt to relocate them. 

IMPORTANT NOTES:

The following models require a single dedicated circuit. 
(One set of wire and ground)

GE04SNLPDG, GE06SNHPDG, GE08SNLPDG, 

GE11SNHPDG, GE15SNHPDG
The following models require two dedicated circuits.
(Two sets or wire and ground).
GE18SNHPDG
The following models require three dedicated circuits 
(Three sets of wire and ground)
GE24DNHPDG, GE27DNHPDG

ELECTRICAL SPECIFICATION GUIDE

NOTE: This guide recommends minimum branch circuit sizing and wire gauge based on the National 

Electric Code.

Model Number

Power (kW)

Voltage

Amps

Recommended Breaker 

Size

Recommended Wire Size

GE04SNLPDG

3.5

120

29

(1 x 30)A

10 AWG

GE06SNHPDG

5.5

240

23

(1 x 30)A

10 AWG

GE08SNHPDG

8.0

240

33

(1 x 40)A

8 AWG

GE11SNHPDG

11.0

240

46

(1 x 50)A

6 AWG

GE15SNHPDG

14.6

240

61

(1 x 70)A

4 AWG

GE18SNHPDG

18.0

240

75

(2 x 40)A

8 AWG

GE24DNHPDG

24.0

240

100

(3 x 40)A

8 AWG

GE27DNHPDG

27.0

240

113

(3 x 40)A

8 AWG

INST

ALLA

TION INSTRUCTIONS

Summary of Contents for GE04SNLPDG























Reviews: