GE Digital Energy SG 400 kVA Operating Manual Download

Page: 82 / 86

Modifications reserved

Page 82/86

OPM_SGS_USM_M40_M50_1US_V020.doc

Operating Manual

SG Series 400 & 500 kVA

8 OPTIONS

8.1 COMMUNICATION OPTIONS

Advanced SNMP Card

Simple Network Management Protocol

The

Advanced SNMP Card

is an interface to the

Ethernet Network

and provides UPS information via the standard

SNMP Protocol

(UPS-MIB (RFC-1628); GE Single MIB; GE Parallel MIB).
The UPS can therefore be managed by a

Network Management

System (NMS)

or by our applications (for instance

JUMP

), which

uses this information to determine the state of the UPS in order to

guarantee safe and orderly shutdown of the server, when
needed.

IRIS Service

Internet Remote Information System

for UPS System.

JUMP Software Suite

Java Universal Management Protocol

Software application for the control and monitoring of the UPS.

Mute

Test

SGT5000_OPT_RMS_01

Stop

Alarm

GE Digital Energy

Remote Signalling Box (RSB)

Equipped with mimic diagram, general alarm, stop operation,
alarm reset and lamp.

8.2 OPTIONS IN UPS CABINET

RPA Kit

Redundant Parallel Architecture

Up to 8 units parallel possible for redundancy or capacity in RPA
configuration.

harmonic f

ilter

Located inside UPS cabinet.

and 11

harmonic f

ilter

Located inside UPS cabinet.

3-wire kit

Located inside UPS cabinet.
To connect the UPS a 3-wire mains input.

FCC Filter

Located inside UPS cabinet. Meets FCC Class A, Part 15
Standard for EMI suppression.

Summary of Contents for Digital Energy SG 400 kVA























































































Search results

Summary of Contents for Digital Energy SG 400 kVA

Reviews:

Related manuals for Digital Energy SG 400 kVA

Brands by name

Popular brands

GE Digital Energy SG 400 kVA, Operating Manual

Search results

Summary of Contents for Digital Energy SG 400 kVA

Reviews:

Related manuals for Digital Energy SG 400 kVA

Brands by name

Popular brands