![background image](http://html.mh-extra.com/html/fsp-technology/eco-600/eco-600_manual-manual_2341012001.webp)
Installation & Operation
1.
Inspection
The following items are inside the box:
●
UPS unit & User manual
•
Remove the UPS from its package and inspect it for damage that
may have occurred during shipping. If any damage is discovered,
re-pack the unit and return it to the place of purchase.
2.
Connect to Utility Power
•
Connect AC power cord to utility power. Then, the UPS will start
to charge inside battery. For best result, charge the battery for 6
hours prior to initial use.
3.
Connect Modem/Phone Line/Network(only for
the model with RJ 11/45 port)
•
This UPS protects a single line (1 in/1 out) phone, modem, or fax
machine from surges when connected through the UPS. Plug in
conning Internet line into the “IN” socket. Use one more Internet
line cable in the “OUT” socket and plug one other end to the
modem input socket.
4.
Plug in Equipment
•
Plug your equipment to Battery Backup Outlets on the rear panel
of the UPS.
NOTE:
Make sure that the UPS is powered on to protect all
important devices from data loss during power failure.
CAUTION:
NEVER connect a laser printer or scanner to the
battery backup outlets of UPS. The equipment may draw
significantly power to overload the UPS.
5.
Connect Com. Port and Install Software(only
for the model with USB com. port)
•
Connect one end of the USB cable to PC and the other to the
USB port at the rear of the UPS.
Product Overview
1:
Power switch with status indicator
2:
Modem/Phone line/Network surge protection
3:
AC input
4:
Circuit breaker
5:
Battery backup outlets (Schuko*3~4, Universal*3, UK*3, NEMA*4~5)
6: Options*
USB com. port /
USB charger
*This option is not available for the selection of 4 x schuko
Operation & Function
Operation:
1.
Turn On the UPS
To turn on the UPS unit, press the power switch lightly. Then, the
LED will light up.
2.
Turn Off the UPS
To turn off the UPS unit, press the power switch again. Then, the
LED will go off.
3.
Cold Start Function
When the UPS is off and there is no power utility, it's stil l possible to
cold start the UPS unit to power the loads.
LED Indicator:
LED
Alarm
UPS Status
●
Off
The mains is normal and UPS
is operated normally.
★
Sounding every 10 seconds
Power failure occurs and UPS
is on battery mode.
★
Sounding every second
Low battery
○
Off
UPS is off.
●
Continuously sounding
UPS fault
●
LED on
○
LED Off
★
LED flashing
MOUNTING UPS
The unit can be mounted to a wall surface.
1.
Use a ruler to draw a straight line in 222 mm
horizontally on the wall. (see chart 1)
2.
Use a sharp nail to puncture the center of the two
ends to mark the wall.
3.
Mount the unit by positioning the key-hole slots
over the mounting nails. (see chart 2)
Chart 1
Chart 2
Placement & Storage
Placement:
Install the UPS in a protected area that is free of excessive dust
and has adequate air flow. Place the UPS away from other units at least
20 cm to avoid interference. For best performance, keep the indoor
temperature between 0° C and 40° C.
Storage:
All connected equipment should be turned off, then disconnect from
the UPS to avoid battery drain. Unplug the UPS from the wall outlet.
Then turn off the UPS for storage. Store the UPS unit covered and
upright in environments where the ambient temperature is -20° C to 50°
C with its battery fully charged.
Line-interactive UPS
ECO 400VA~800VA
FSP Manual Guide