GE DHDVH52 Technical Service Manual Download Page 46 | Manualshive

Page: 46 / 50

background image

T e s t

Mode

Press

Displays

Exit

t01

Start/
Pause

Displays UI model number (01-16) that corresponds to the UI model
the control is currently conﬁ gured for. Always displays"---" when no
model is set in the control board. Proper model must be set when
control board replaced. Rotate knob until desired UI model number
is displayed (01-03), then press and hold Start/Pause until beep.

Press Power
Returns to t01

t02

Start/
Pause

Displays the most recent error code. Control will store 8 error codes
(E00=none). Press Start/Pause to clear each error code and display
the next. Press and hold Start/Pause to clear all error codes (will
then display E00).

Press Power
Returns to t02

t03

Start/
Pause

Displays software and non-volatile revision numbers. Presents
software revision number ﬁ rst. Press and hold Start/Pause to select
non-volatile revision number.

Press Power
Returns to t03

t04

Start/
Pause

Non-volatile memory test. The control will compute and compare
the 16-bit CRC of the non-volatile memory with the pre-computed
16-bit CRC stored in the non-volatile memory. The control will sound
the key press beep and display "EEP" after successful comparison,
or sound the invalid key beep and display "Err" if unsuccessful.

Press Power
Returns to t04

t05

Start/
Pause

Turns on all LEDs and the 7-segment display.

Press Power
Returns to t05

t06

Start/
Pause

The control will sound a beep as long as any key is pressed.

Press Power
Returns to t06

t07

Start/
Pause

Turns on motor and inner coil (electric) or burner (gas). Displays
outlet thermistor temperature in degrees Fahrenheit.

Press Power
Returns to t07

t08

Start/
Pause

Turns on motor and inner coil (electric) or burner (gas). Displays inlet
thermistor temperature in degrees Fahrenheit.

Press Power
Returns to t08

t09

Start/
Pause

Displays voltage read from the moisture sensor in volts.

Press Power
Returns to t09

t10

Start/
Pause

Displays the condition of the exhaust system. The test takes
approximately 2 minutes to complete. The control measures
the rate of temperature increase through the inlet thermistor
for a duration of 30 seconds. An acceptable increase is 48°F
(9°C) for electric and 62°F (17°C) for gas. “LO” = exhaust too
small or restricted. “HI” = exhaust adequate. (Note: “HOT”
indicates the test was not completed normally. This test must
be initiated when the inside of the dryer is cool).

Press Power
Returns to t10

«
...
44
45
46
47
48
...
»

Summary of Contents for DHDVH52



















































Reviews:

No comments

Related manuals for DHDVH52

Brand: Cosori Pages: 23

Brand: Emerald Pages: 32

Brand: Comelec Pages: 6

Frymaster FPEL114C

Brand: Welbilt Pages: 40

Brand: Morris Pages: 4

Brand: Maytag Pages: 44

Brand: Indesit Pages: 16

Brand: Kitchen Advance Pages: 10

Brand: HAEGER Pages: 24

Brand: Splendide Pages: 24

Brand: American Dryer Corp. Pages: 62

Brand: Asko Pages: 24

DDAD T-30 2 Series

Brand: Dexter Laundry Pages: 8

Brand: ELEKTRA Pages: 56

Brand: Philips Pages: 56

Brand: Electrolux Pages: 26

Brand: Electrolux Pages: 23

Brand: Electrolux Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands