manualshive.com logo in svg

GE auisys cs2, User'S Reference Manual

The GE Auisys CS2 User's Reference Manual is a comprehensive guide packed with all the necessary information to effortlessly operate your device. This well-structured manual can be downloaded for free from our website, allowing you to access it anytime, anywhere. Enhance your user experience with our downloadable manual at manualshive.com.

Share
Download
background image

Using the brake

The central brake holds the system in place.

Do not use the brake while moving the anesthesia

system. This could cause the machine to tip over. Only

use the brake to keep the system in place.

AC.22.009

1.

Push down on the brake pedal to lock the system in place.

2.

Lift up on the brake pedal to release the brake.

Using the O2 flush button

The O2 flush button supplies a high flow of O2 to the breathing
system.

1.

Push the O2 flush button to deliver a high flow of O2.

2.

Release the O2 flush button to stop the delivery of a high flow of
O2.

Positioning the display

The display can be moved for optimal viewing.

1.

Unlock the display arm.

2.

Raise or lower the display arm to adjust the height of the
display.

3.

Lock the display arm.

4.

Rotate the display arm toward or away from the system to adjust
the horizontal position of the display.

5.

Tilt the display up or down to adjust the vertical angle of the
display.

WARNING

Aisys CS²

2-4

2067226-001

Summary of Contents for auisys cs2













































































































































































































































































Reviews:

No comments

Related manuals for auisys cs2

Taurus B450 Assembly Instructions Manual preview
B450
Brand: Taurus Pages: 28
Kärcher HDS Series Operator'S Manual preview
HDS Series
Brand: Kärcher Pages: 54
ABB 2 Series Operation And Installation Manual preview
2 Series
Brand: ABB Pages: 85
DARAY X200 Operating & Installation Manual preview
X200
Brand: DARAY Pages: 28
MacDon 3020 Operator'S Manual preview
3020
Brand: MacDon Pages: 88
Jiffy 56 Operating Manual/Parts Manual preview
56
Brand: Jiffy Pages: 15
A.MENARINI GlucoMen Areo Quick Manual preview
GlucoMen Areo
Brand: A.MENARINI Pages: 2
B&G H5000 Pilot Calibration Manual preview
H5000 Pilot
Brand: B&G Pages: 3
MADRIX NEO Quick Start Manual & Technical Manual preview
NEO
Brand: MADRIX Pages: 12
Narcotrend Compact M Operating Instructions Manual preview
Compact M
Brand: Narcotrend Pages: 47
IFM AC1401 Device Manual preview
AC1401
Brand: IFM Pages: 175
IFM VSE150 Installation Instructions preview
VSE150
Brand: IFM Pages: 5
PASCO ME-9430 Instruction Manual And Experiment Manual preview
ME-9430
Brand: PASCO Pages: 30
Mainpine IQ Express RF6118 Quick Start Manual preview
IQ Express RF6118
Brand: Mainpine Pages: 2
Joyolight CON-WH-1Z User Manual preview
CON-WH-1Z
Brand: Joyolight Pages: 4
Ridder SynCore RW Unit Product Manual preview
SynCore RW Unit
Brand: Ridder Pages: 28
Pfeuffer 1520 9001 Operating Instructions Manual preview
1520 9001
Brand: Pfeuffer Pages: 32
WATSON INDUSTRIES AHRS-E304 Owner'S Manual preview
AHRS-E304
Brand: WATSON INDUSTRIES Pages: 17

Brands by name

Popular brands

Load more brands