GEAppliances.com
Select Options (Continued)
Steam
For use with heavily soiled and/or dried-on, baked-on soils. This option
MUST
be selected
PRIOR
to
(Prewash)
starting the cycle. The
Steam
option adds approximately 30 minutes to the cycle time. This option is
(on some models) available
with
Heavy
,
Auto Sense
, and
Normal
cycles.
Wash
Selecting either the Upper or Lower
Wash Zones
will target dishwashing of just one rack. This will
Zones
shorten the cycle time and conserve energy. This option can be used when there is only half a
(on some models)
load of dishes.
Delay
Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press
Delay Hours
, to select
Hours
the number of hours, then press
Start
one time to begin countdown. The cycle will start once allotted time
(on some models)
has expired.
Control
You can lock the controls to prevent selections from being made. You can also lock the controls
Lock
after you have started a cycle to prevent cycle changes. For example, children cannot accidentally
start the dishwasher by pressing pads with this option selected.
To LOCK the dishwasher control
,
depending on the model, press and hold the
Heated Dry
pad for 3 seconds or
press and hold the
Steam
and
Wash Temp
pads at the same time for 3 seconds. The Control Lock light will turn
on to indicate the control is locked
.
To UNLOCK the dishwasher control
,
depending on the model, press and hold the
Heated Dry
pad for 3 second
or press and hold the
Steam
and
Wash Temp
pads at the same time for 3 seconds. The Control Lock light
will turn off to indicate the control is unlocked.
Energy
When connected to a smart meter and your electric company, the dishwasher will automatically delay starting
Smart
a cycle during the more expensive peak demand times, and run when demand is low. However, you can override
the delay settings and use the dishwasher as needed. Learn more about
Energy Smart
under the
Using the
Dishwasher
section.
Start Dishwasher
Start
Door can be open to select the desired options. Press the
Start
pad and close the door within 10 seconds
to start the cycle or begin the
Delay Hours
countdown. The wash cycle will begin shortly after closing
the door. If the door is open, the illuminated lights will turn off if a pad is not pressed within two minutes.
To activate the display, close and open the door or press any pad.
Interrupt
To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash cycle to
or
Pause
pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume
the cycle, press
Start
, and close the door.
Cancel
To cancel a wash cycle, press and hold the
Start
pad for 3 seconds and close door. The dishwasher will drain,
emit a beep sound, and the wash cycle light will turn OFF.
Cycle Completion
Sanitized
Displayed at the end of the cycle when
Wash Temp Sani
(Sanitize)
has been selected and the dishwasher has met the
requirements for sanitization. See
Wash Temp Sani
, for complete option description. Opening the door or pressing any
key while the door is closed will turn off the light.
Clean
Displayed when a wash cycle is complete. The light stays
ON
as a reminder that the dishes are clean. Opening
the door or pressing any key while the door is closed will turn the light off.
Door Wake
To turn this option
ON/OFF
, press and hold the
START
and
WASH TEMP
pads for 5 seconds, close the door and wait
Up Mode
3 minutes for the dishwasher to go into sleep mode. In the
OFF
mode, the control display, control sounds,
(on some models)
and interior lights will not respond to the door opening/closing. This mode can be used when observing certain
religious holidays such as the Sabbath. To activate the control and interior lights, press any pad.
5
6
5
7
