background image

1

AL-2017/AL-3017 Installation Manual

Contents

Introduction ............................................................................................................. 2

Installation ................................................................................................................ 3

System Wiring .......................................................................................................... 5

Earth grounding ...................................................................................................................................... 5

System bus connection ........................................................................................................................... 5

Shielded cable routing ............................................................................................................................ 6

Auxiliary power supply connections ...................................................................................................... 6

PSTN wiring ........................................................................................................................................... 7

AL-2017/AL-3017 Wiring ....................................................................................... 8

Basic Programming ............................................................................................... 10

Programming Steps ............................................................................................... 12

Text words ............................................................................................................................................ 12

Time zones ............................................................................................................................................ 12

Areas ..................................................................................................................................................... 12

Alarm groups ........................................................................................................................................ 13

Remote arming stations (RAS) ............................................................................................................. 13

Data gathering panels (DGP) ............................................................................................................... 13

Zone (inputs) ........................................................................................................................................ 14

Communication options ....................................................................................................................... 15

New installer code ................................................................................................................................ 15

Relays (outputs) .................................................................................................................................... 16

Battery Capacity .................................................................................................... 17

Battery calculation worksheet example ................................................................................................ 18

Absolute maximum loads ..................................................................................................................... 18

Battery calculation worksheet .............................................................................................................. 19

FCC Compliance .................................................................................................... 20

UL Compliance ...................................................................................................... 20

Specifications .......................................................................................................... 22

©  200

9

 GE Security. All rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system, or

transmitted in any form, or by any means – electronic, photocopying, recording, or otherwise – without the prior written permission of GE
Security. GE Security reserves the right to change information without notice.

Summary of Contents for Alliance AL-2017

























Reviews: