5
GEAppliances.com
Cool Mode
Use the
Cool
mode at
Low, Med, High
or
Auto Fan
Speed
for cooling. Use the
Temperature Increase
Ÿ
/
Decrease
ź
pads to set the desired temperature
between 64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on
and off to keep the room at the set level of comfort.
Set the thermostat at a lower number and the indoor
air will become cooler. Set the thermostat at a higher
number and the indoor air will become warmer.
NOTE:
If the air conditioner is off and is then turned on
while set to a
Cool
setting or if turned from a fan
setting to a
Cool
setting, it may take approximately
3 minutes for the compressor to start and cooling to
begin.
Cooling Descriptions
For Normal Cooling
³6HOHFWWKH
Cool
mode and
High
or
Med
fan with a middle set temperature.
For Maximum Cooling
³6HOHFWWKH
Cool
mode
and
High
fan with a lower set temperature.
For Quieter and Nighttime Cooling
³6HOHFWWKH
Cool
mode and
Low
fan with a middle set
temperature.
Fan Only Mode
Use the Fan Only Mode at Low, Med or High fan
speed to provide air circulation and filtering without
cooling. Since fan-only settings do not provide
cooling, a Set temperature cannot be entered. The
room temperature will appear in the display.
NOTE:
Auto Fan Speed cannot be used when in the
Fan Only
Mode.
Energy Saver Mode
In the case of a power outage or interruption, the
unit will automatically restart in the settings last
used after the power is restored. If the
Delay 1–24hr
feature was set, it will resume countdown. You may
need to set a new time if desired.
Power Outage Recovery Feature
Set to
Auto
fan speed for the fan speed to
automatically set to the speed needed to provide
optimum comfort settings with the set temperature.
If the room needs more cooling, the fan speed
will automatically increase. If the room needs less
cooling, the fan speed will automatically decrease.
NOTE:
Auto Fan Speed cannot be used when in the
Fan Only
Mode.
Auto Fan Speed
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for
freezing outdoor conditions. It must not be used in
freezing outdoor conditions.
To ensure proper operation, aim the remote
control at the signal receiver on the air
conditioner.
Make sure nothing is between the air conditioner
and the remote control that could block the
signal.
The remote control signal has a range of
up to 20 feet.
Make sure batteries are fresh and installed
correctly as indicated on the remote control.
Remote contains a magnet allowing it to attach
to metal surfaces.
Remote Control
This mode optimizes the cooling power of your air
conditioner, thereby saving you energy. Once the
set point temperature has been reached, the fan
will cycle off to save energy. The fan will cycle back
on periodically to insure all cooling capacity in the
system is used. This mode is the default mode for the
unit. Each time the unit is powered off, it will restart
in
Energy Saver
mode
ON
. This includes
Delay
timer
mode. The first time the unit is turned on, the settings
will be 70° and
Low
fan. You can adjust the fan
speed and temperature to your personal comfort.
Energy Saver ON
³
Helps minimize electricity use.
It is normal for the fan to cycle off and then back
on in this mode. This on/off cycle can repeat
multiple times. Because the fan will cycle off, you
may notice a variation in room temperature and
humidity.
Energy Saver OFF
³
When this mode is not engaged,
the fan will run continuously, and in
Cool
mode the
compressor will cycle on and off to maintain room
temperature.
Summary of Contents for AEM14 Series
Page 16: ...16 Notes...
Page 47: ...47 Notas GEAppliances com...
Page 48: ...48 Notas...
Page 49: ...49 Notas GEAppliances com...
