GE 600-1021-95R Installation Instructions Manual Download Page 88

Page: 88 / 113

Concord 4 Series Systems

These devices not listed, investigated, or verified by UL.

** UL listing applied for.

†

Listed, but not tested for compatibility by UL.

††

Total current only for all 2-wire smoke detectors connected to panel 2-wire smoke loop.

Note

When installing SuperBus 2000 RF Receiver Modules, the Antenna Tamper feature must be set to off

(see REPORTING—GLOBAL in the “Programming” section).

Table A2: Hardwire Devices

Part No.

Description

Qty.

(Max.)

Sub Total

Hardwire Sensors/Detectors

N/A

System Sensor models 2400, or 2400TH or ESL

series 429AT, 521B or 521BXT

80 mA

††

13-082*

PIR Motion Detector

10 mA

Sirens

13-046

Hardwire Exterior Siren

145 mA

13-949**

Hardwire Interior Siren

85 mA

13-950**

Piezo Dynamic Exterior Siren

150 mA

SuperBus 2000/Miscellaneous Components

60-746-01

2x16 LCD Alphanumeric Touchpad

90 mA

60-820

Fixed Display LCD Touchpad

65 mA

60-803

2x20 LCD Alphanumeric Touchpad

120 mA

60-804

2x20 VFD Alphanumeric Touchpad

120 mA

60-983

ATP 1000

110 mA

60-984

ATP 2600

165 mA

60-985

ATP 2100

165 mA

600-1013*

GTS 50

300 mA

60-836

Voice Only Module (with current jumper installed)

(with current jumper removed)

300 mA

600 mA

60-777-01

Phone Interface/Voice Module

600 mA

600-1025-01-

95R

RF Transceiver

55 mA

60-764-01-95R RF Receiver (see note)

35 mA

600-1019

2 Amp Power Supply

N/A

60-756

4 Input/2 Output SnapCard

185 mA

60-757

8Z Hardwire Zone Expander SnapCard

230 mA

60-758

4 Output SnapCard

130 mA

60-774

Hardwire Input Module

35 mA

60-770

Hardwire Output Module

180 mA

60-620-01*

Energy Saver Module

20 mA

60-850
60-850-01

Cellular Backup Module (standard power)
Cellular Backup Module (high power)

1600 mA
1900 mA

60-861

Wireless Gateway-Ready Kit

1600 mA

60-677*

Interrogator 200 Audio Verification Module

10 mA

60-783-02*

Automation Module

35 mA

60-528

Hardwire Interior Speaker

500 mA

13-060

15-Watt Speaker

500 mA

Total power consumption:

Total power consumption not to exceed:

1,000 mA

WWW.DIYALARMFORUM.COM

Summary of Contents for 600-1021-95R


















































































































Search results

Summary of Contents for 600-1021-95R

Reviews:

Related manuals for 600-1021-95R

Brands by name

Popular brands

GE 600-1021-95R, Installation Instructions Manual

Search results

Summary of Contents for 600-1021-95R

Reviews:

Related manuals for 600-1021-95R

Brands by name

Popular brands