GE 600-1021-95R Installation Instructions Manual Download Page 61

Page: 61 / 113

Concord 4 Series Systems

Accessory Modules Menu

The

ACCESSORY MODULES

menu gives you access to the following menus:

•

BUS DEVICES

—this menu lets you read bus device unit numbers, assign bus devices to a par-

tition, and configure other features associated with a specific bus device.

•

SNAPCARDS

—this menu lets you set the configuration number for each SnapCard output,

assign SnapCard outputs to a partition, and name the SnapCard outputs.

The following describes how to program the settings that appear under

ACCESSORY MODULES—

BUS DEVICES

Vox RX Gain

(09010)

Audio Verification-Partition 1 (Default = 08)

This setting determines the receiver (talkback) gain

level for voice-activated switching (VOX). Setting

range is 01-10.
If the VOX is switching the speaker on when the

central station operator is not talking, lower this

setting and the VOX Mic Gain setting.
If the VOX is

not

switching the speaker on when

the central station operator is talking, raise this set-

ting and lower the VOX Mic Gain setting.

To change the VOX RX Gain:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

VOX RX GAIN nn

(current setting)

2. Enter the desired

2-digit setting

(01 - 10). The display flashes the

entered setting. Press # and the display shows the new setting.

Unit-ID

(10000 thru 10015)

Acc. Modules-Bus Devices (Default = **** or none)

This menu lets you identify all connected bus

devices, view each Unit Number, view the Device

ID number, and configure other settings based on a

specific device. This menu also lets you delete

learned bus devices.

Note

Most settings under ACCESSORY MODULES—BUS

DEVICES have no shortcut numbers.

To help identify bus devices, the 8-digit Device ID

number is also located on a label on each Super-

Bus 2000 device.

To identify bus device Unit and ID:

1. With the display showing

BUS DEVICES

, press #. The display shows

the bus Unit Number and the 8-digit Device ID number. For exam-

ple:

UNIT - ID 0—02110185

. Where

is the Unit Number and

02110185

is the Device ID number.

2. Press A or B to identify all other bus Unit Numbers (0–15) and

Device ID numbers.

To delete learned Unit Numbers:

1. With the display showing

BUS DEVICES

, press #. The display shows

the bus device set to Unit Number 0.

2. Press A or B until the bus device Unit Number you want to delete is

displayed.

3. Press D. The display changes the Unit Number to

NONE

Device ID

Acc. Modules-Bus Devices-Unit ID-Change ID (Default = none)

This menu lets you change the bus

device ID number when replacing

a defective bus device.

To change a Device ID:

1. With the display showing the desired bus device, press # + #. The display shows

DEVICE ID

(current ID)

2. Enter the ID of the new bus device. The display flashes the entered selection. Press #

and the display shows the new setting.

3. Exit programming mode.

4. Remove AC and battery power from the panel.

5. Replace the defective bus device with a new one.

6. Apply AC and battery power to the panel.

WWW.DIYALARMFORUM.COM

Summary of Contents for 600-1021-95R


















































































































Search results

Summary of Contents for 600-1021-95R

Reviews:

Related manuals for 600-1021-95R

Brands by name

Popular brands

GE 600-1021-95R, Installation Instructions Manual

Search results

Summary of Contents for 600-1021-95R

Reviews:

Related manuals for 600-1021-95R

Brands by name

Popular brands