GE Security Simon XT V2 Installation Manual Download Page 1

GE

 

Security 

Simon XT V2 Installation Guide 

Content 

Contact information   1

 

Description   1

 

Installation   1

 

Connecting hardwired devices   2

 

Wiring phone lines   2

 

Wiring the power transformer   3

 

Programming   3

 

Sensor testing   6

 

Specifications   7

 

Regulatory information   7

 

 

Contact information 

For contact information see our Web site: 
www.gesecurity.com. 

Description 

 

© 2010 GE Security, Inc. 

P/N 466-2375 • REV A • ISS 24FEB10 

This is the Installation Guide for the Simon XT control panel 
(model 600-1054-95R-V2). 

The system can monitor up to 40 sensors including: 

• Door/Window 

sensor 

(60-670) 

•  Indoor motion sensor (60-639) 
• Outdoor 

motion 

sensor (60-639) 

•  Remote handheld touchpad (60-671) 

Contact your GE representative for a more complete list.

Caution: 

Do not use outdoor motion sensors for intrusion 

protection 

 

 

 

Table 1 below describes the recommended sensor groups. 

Table 1: Recommended sensor groups 

Device 

Recommended sensor group 

Indoor motion sensor 

17 

a

  

Outdoor motion sensor 

25 (chime only group) 

b

Entry/exit door 

10 

Interior door 

14 

Window sensor  

13 

Smoke sensor 

26 

c

Key fob 

01 

ELM key fob 

01 

Remote handheld touchpad 

01 

CO alarm 

34 

b

Freeze sensor 

29 

b

Water sensor 

38 

b

Personal help button 

01 

a. 

Not certified as a primary protection circuit for UL-listed 
systems and is for supplementary use only. 

b. 

Has not been investigated by UL. 

c. 

Required for UL-listed residential fire alarm applications. 

Installation 

Tabs at the top of the panel secure and release the front 
cover and the chassis. The plastic hinges on the panel 
bottom allow the cover and chassis to swing down and out 
of the way. 

To mount the panel on a wall: 

1.  Choose a panel location. 

2.  Run all necessary power, phone, siren, and hardwired 

contact wires to the desired panel location. 

Summary of Contents for Simon XT V2









Reviews: