manualshive.com logo in svg

GE Security 1200C, Installation Manual

Share
Download
GE Security 1200C Installation Manual Download Page 40

 

36 

1200C-2000C Fire Alarm Control Panel, Repeater, and Black Box Installation Manual 

Module Installation 

location 

FEP2000N 

Inside the cabinet box 

LC1502 

Inside the cabinet box 

SD2000 

Inside the cabinet box 

PS1200N 

Inside the cabinet box 

NC2011 

Inside the cabinet door (top layer) 

NC2051 

Inside the cabinet door (top layer) 

LON2000 

Inside the cabinet door (top layer) 

RB2016 

Inside the cabinet box 

 

Installed modules for fire panels, repeaters, and black boxes 

The modules installed in each control panel are listed in the following tables. These 
listings exclude the HDIS2000, FC1200-FC2012, KPD2000, and LCD1200 modules. 

Table 9: Fire panel modules 

Panel 

Modules 

     

FP1216N ZE2016  FEP2000N 

PS1200N LC1502  SD2000  PS2000N 

FP1264N ZE2064  FEP2000N 

PS1200N LC1502  SD2000  PS2000N 

FP28255C ZE2064  FEP2000N PS1200N LC1502  SD2000  PS2000N 

FP2864C ZE2016  FEP2000N 

PS1200N LC1502  SD2000  PS2000N 

Regional variants: 
•  German panels have a VDS2000 module instead of the SD2000 module 
•  French panels do not have the SD2000 module 
•  Danish and Swedish panels have the LON2000 module 

Table 10: Repeater and global repeater modules 

Panel 

Modules 

     

FR1216N ZE2016  --- 

PS1200  --- 

NC2011  NE2011 

FR1264N ZE2064  --- 

PS1200  --- 

NC2011  NE2011 

FR20255N ZE2064  --- 

PSH2000  PSDC2000 NC2011  NE2011 

FR2064N ZE2016  --- 

PSH2000 PSDC2000 

NC2011  NE2011 

FRG20255N ZE2064 

FEP2000N  PS1200N PS2000N NC2011  NE2011 

GR2064C  ZE2016  --- 

PS1200N PS2000N NC2011  NE2011 

 

Table 11: Black box modules 

Panel 

Modules 

     

FB2800C FEP2000N 

PS1200N LC1502  PS2000N NC2011 NE2011 

 

Summary of Contents for 1200C

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands