manualshive.com logo in svg

GE Security 1200C, Installation Manual

Share
Download
GE Security 1200C Installation Manual Download Page 32

 

28 

1200C-2000C Fire Alarm Control Panel, Repeater, and Black Box Installation Manual 

Commissioning networks 

Once the control panel has been commissioned correctly, the following steps are 
required to initialize and configure a network. 
1.  Configure the network setup (via the Setup menu or using a PC) 
2.  Investigate and fix all faults that are reported 
3.  Check the status of the systems on the ARCNET network that are configured to 

communicate with the repeater. Faults regarding communication with repeater 
node identification address should disappear when the ARCNET network is 
operational 

4.  Check all connections to panels by emulating them 
5.  Check panel fault reporting by switching off each panel one by one and checking 

that the missing panel is reported by the other panels in the network 

6.  Check fire and fault reporting 
7.  Check all that all network input and output devices are working correctly 
8.  Reset all repeaters and control panels 

Summary of Contents for 1200C

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands