GE Multilin 469 Instruction Manual Download | Manualshive

Page: 176 / 338

background image

5–34

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

5.5

S4 Output Relays

5.5.1

Description

Five of the six output relays are always non-failsafe; the 6 SERVICE relay is always failsafe.
As failsafe, the 6 SERVICE relay will be energized normally and de-energize when called
upon to operate. It will also de-energize when control power to the 469 is lost and
therefore, be in its operated state. All other relays, being non-failsafe, will be de-energized
normally and energize when called upon to operate. Obviously, when control power is lost
to the 469, the output relays must be de-energized and therefore, they will be in their non-
operated state. Shorting bars in the drawout case ensure that when the 469 is drawn out,
no trip or alarm occurs. The the 6 SERVICE relay will however indicate that the 469 has
been drawn out.

5.5.2

Relay Reset Mode

PATH: SETTINGS

ZV

S4 OUTPUT RELAYS

Z

RELAY RESET MODE

A latched trip or alarm may be reset at any time, providing that the condition that caused
the trip or alarm is no longer present. Unlatched trips and alarms will reset automatically
once the condition is no longer present. If any condition may be reset, the Reset Possible
LED will be lit. All Block Start features reset automatically when the lockout time has
expired and the trip has been reset.

The other relays may be programmed to All Resets which allows reset from the front
keypad or the remote reset switch input or the communications port. Optionally, relays 1
through 6 may be programmed to reset by the “Remote Reset Only” (by the remote reset
switch input or the communications port) or “Keypad Reset Only” (reset only by relay
keypad).

NO

trip or alarm element must

EVER

be assigned to two output relays where one is

Remote Reset Only and the other is Keypad Reset Only. The trip or alarm will not be
resettable if this occurs.

RELAY

[

1 TRIP:

All Resets

Range: All Resets, Remote Reset Only,

Keypad Reset Only

MESSAGE

2 AUXILIARY:

All Resets

Range: All Resets, Remote Reset Only,

Keypad Reset Only

MESSAGE

3 AUXILIARY:

All Resets

Range: All Resets, Remote Reset Only,

Keypad Reset Only

MESSAGE

4 ALARM:

All Resets

Range: All Resets, Remote Reset Only,

Keypad Reset Only

MESSAGE

5 BLOCK START:

Auto-Reset

Range: N/A

MESSAGE

6 SERVICE:

All Resets

Range: All Resets, Remote Reset Only,

Keypad Reset Only

«
...
174
175
176
177
178
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: Zander Aachen Pages: 4

Brand: Basler Pages: 135

Brand: Entes Pages: 2

Brand: System Sensor Pages: 2

Brand: Nassar Pages: 5

Brand: NetPing Pages: 22

Brand: SafeTrust Pages: 10

Brand: Woodward Pages: 35

Brand: Simply Automated Pages: 2

Brand: System Sensor Pages: 4

Allen-Bradley Guardmaster Minotaur MSR142RTP

Brand: Rockwell Automation Pages: 4

Brand: Rockwell Automation Pages: 6

Brand: CARLO GAVAZZI Pages: 7

Revo C 2PH 1100A

Brand: CD Automation Pages: 84

REVO C 3PH 1100A

Brand: CD Automation Pages: 91

Brand: SVS Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands