GE HEALTHCARE CARESCAPE Monitor B650 Technical Manual Download Page 119 | Manualshive

Page: 119 / 240

background image

Installation checkout

111

2062973-002

monitor battery and disconnecting the power cord from the wall outlet for a moment before
turning the monitor on.
Verify that the patient monitor starts up normally:

−

The yellow, red and blue alarm lights are lit momentarily.

−

The speaker gives an audible beep.

−

The normal monitoring screen appears and there are no error messages on the
screen.

NOTE: Refer to section

11. Troubleshooting

to see the procedure for battery conditioning and

battery replacement, if you receive a

Condition monitor battery

or a

Battery Failure

message.

NOTE: Before taking the patient monitor into use for the first time, the battery should be fully
charged. Keep the monitor connected to the mains until the battery is fully charged.

8.3.2 Display

Picture quality

Perform this test both for the integrated main display and for the optional secondary display.
1.

Verify that all text is readable and all images are clear.

2.

Verify that the brightness is good. Adjust if necessary.

Touchscreen control

Perform this test only if the integrated main display or the optional secondary display is a
touchscreen.
1.

Verify the operation and the calibration of a touchscreen by touching a corner of an
active parameter window. Verify that the selected menu is opened.

2.

Select

to close any open menu and return to the main display.

8.3.3 Device Information

1.

Log in to Webmin.

2.

Select

Information >

Device Information

.

3.

Verify that the device information is correct:

−

The connected parameter modules are identified.

−

The connected CARESCAPE Network ID interfaces are identified.

−

The connected USB input devices are identified.

4.

Stay connected to Webmin.

8.3.4 Configuration Information

1.

Select

Information >

Configuration Information

.

2.

Verify that the patient monitor is correctly configured:

−

The host Information is correct.

−

The active software package is correct.

−

The correct host licenses are enabled.

−

The correct PDM licenses are enabled.

−

Patient ID prefix is correctly configured.

−

Unit and Bed name are correctly configured.

«
...
117
118
119
120
121
...
»

Summary of Contents for CARESCAPE Monitor B650

















































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B650

Brand: zipwake Pages: 2

Brand: zipwake Pages: 2

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: B. Braun Pages: 2

Aesculap Neurosurgery

Brand: B. Braun Pages: 13

Aesculap AdTec mini

Brand: B. Braun Pages: 2

Brand: B.Well Pages: 2

Brand: B. Braun Pages: 55

BA Ultimate LED

Brand: B.A. International Pages: 234

Brand: OHAUS Pages: 84

Brand: Tar River Pages: 61

Smart Plus PHT-35LHS

Brand: Vatech Pages: 190

Brand: H&S Pages: 54

Brand: Samson Pages: 2

UG 2200 Special

Brand: Amazone Pages: 252

Brand: HOFFEN Pages: 22

Brand: KEP Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands