manualshive.com logo in svg

GDI COMMUNICATIONS SM336, Manual

Share
Download
GDI COMMUNICATIONS SM336 Manual Download Page 28

SM336 Manual 

 

 

       

25

 

5  

CONNECT 1200 

The modem has connected to the line and either the line speed is 1200 bps and DCE speed reporting is 
enabled, or the DTE speed is 1200 bps and DTE speed reporting is enabled. 

6 

NO DIALTONE 

For X2 and X4, the modem has been instructed to wait for dial tone during dialing but none is received. 
When cellular phone interface is selected, indicates that cellular service is not currently available. 

7  

BUSY 

For X3 and X4, if busy tone detection is enforced, the busy (engaged) signal is detected on the line 
when the modem is attempting to originate a call. 

8  

NO ANSWER 

The modem is attempting to originate a call if a continuous ringback signal is detected on the line until 
the expiration of the timer S7. 

9 

CONNECT 0600 

The modem has connected to the line, the DTE speed is 600 bps, and DTE speed reporting is enabled. 

 

 

 

10  

CONNECT 2400 

The modem has connected to the line and either the line speed is 2400 bps and DCE speed reporting is 
enabled, or the DTE speed is 2400 bps and DTE speed reporting is enabled. 

11 

CONNECT 4800 

The modem has connected to the line and either the line speed is 4800 bps and DCE speed reporting is 
enabled, or the DTE speed is 4800 bps and DTE speed reporting is enabled. 

12  

CONNECT 9600 

The modem has connected to the line and either the line speed is 9600 bps and DCE speed reporting is 
enabled, or the DTE speed is 9600 bps and DTE speed reporting is enabled. 

13  

CONNECT 7200 

The modem has connected to the line at 7200 bps and DCE speed reporting is enabled. 

14  

CONNECT 
12000 

The modem has connected to the line at 12000 bps and DCE speed reporting is enabled. 

15  

CONNECT 
14400 

The modem has connected to the line at 14400 bps and DCE speed reporting is enabled. 

16  

CONNECT 
19200 

The modem has connected to the line and either the line speed is 19200 bps and DCE speed reporting 
is enabled, or the DTE speed is 19200 bps and DTE speed reporting is enabled. 

17  

CONNECT 
38400 

The modem has connected to the line, the DTE speed is 38400 bps, and DTE speed reporting is 
enabled. 

18  

CONNECT 
57600 

The modem has connected to the line, the DTE speed is 57600 bps, and DTE speed reporting is 
enabled. 

19  

CONNECT 
115200 

The modem has connected to the line, the DTE speed is 115200 bps, and DTE speed reporting is 
enabled. 

22  

CONNECT 
75TX/1200RX 

The modem has established a V.23 originate connection and line speed reporting is enabled. 

23  

CONNECT 
1200TX/75RX 

The modem has established a V.23 answer connection and line speed reporting is enabled. 

24  

DELAYED 

For X4, sent when a call fails to connect and the number dialed is considered 'delayed' due to country 
blacklisting requirements. 

32 

 

BLACKLISTED 

For X4, sent when a call fails to connect and the number dialed is considered 'blacklisted'. 

33  

FAX 

A fax modem connection is established in a facsimile mode. 

35  

DATA 

A data modem connection is established in a facsimile mode. 

40  

CARRIER 300 

The modem has connected to the line at 0-300 bps and carrier reporting is enabled. (See S95 and Xn.) 

44  

CARRIER 
1200/75 

The V.23 backward channel carrier is detected and carrier reporting is enabled. (See S95 and Xn.) 

45  

CARRIER 
75/1200 

The V.23 forward channel carrier is detected and carrier reporting is enabled. (See S95 and Xn.) 

46  

CARRIER 1200 

The modem has connected to the line at 1200 bps and carrier reporting is enabled. (See S95 and Xn.) 

47  

CARRIER 2400 

The modem has connected to the line at 2400 bps and carrier reporting is enabled. (See S95 and Xn.) 

48  

CARRIER 4800 

The modem has connected to the line at 4800 bps and carrier reporting is enabled. (See S95 and Xn.) 

49  

CARRIER 7200 

The modem has connected to the line at 7200 bps and carrier reporting is enabled. (See S95 and Xn.) 

50  

CARRIER 9600 

The modem has connected to the line at 9600 bps and carrier reporting is enabled. (See S95 and Xn.) 

51  

CARRIER 12000 

The modem has connected to the line at 12000 bps and carrier reporting is enabled. (See S95 and Xn.) 

52  

CARRIER 14400 

The modem has connected to the line at 14400 bps and carrier reporting is enabled. (See S95 and Xn.) 

53  

CARRIER 16800 

The modem has connected to the line at 16800 bps and carrier reporting is enabled. (See S95 and Xn.) 

54  

CARRIER 19200 

The modem has connected to the line at 19200 bps and carrier reporting is enabled. (See S95 and Xn.) 

55  

CARRIER 21600 

The modem has connected to the line at 21600 bps and carrier reporting is enabled. (See S95 and Xn.) 

56  

CARRIER 24000 

The modem has connected to the line at 24000 bps and carrier reporting is enabled. (See S95 and Xn.) 

57  

CARRIER 26400 

The modem has connected to the line at 26400 bps and carrier reporting is enabled. (See S95 and Xn.) 

58  

CARRIER 28800 

The modem has connected to the line at 28800 bps and carrier reporting is enabled. (See S95 and Xn.) 

59  

CONNECT 
16800 

The modem has connected to the line, the DTE speed is 16800 bps and DTE speed reporting is 
enabled. 

61  

CONNECT 
21600 

The modem has connected to the line, the DTE speed is 21600 bps and DTE speed reporting is 
enabled. 

62  

CONNECT 
24000 

The modem has connected to the line, the DTE speed is 24000 bps and DTE speed reporting is 
enabled. 

Summary of Contents for SM336
































Reviews:

No comments

Brands by name

Popular brands

Load more brands