background image

6. Setting up the Ethernet gateway for use with iG-HUB Express

iG-HUB Express (PC Software) Setup

Visit http://www.G-HUB.com/support/downloads/ to download and install the iG-HUB 
Express software. 

 

•  Launch the iG-HUB Express installer and follow the on-screen instructions. 

•  Launch the iG-HUB Express program. 

 
 
 
 

•  Activate the Express software with the code you received when purchasing. 

 

 

 
 
 
 
 
 
 
 

•  Add the gateway(s) and wireless sensors to the software. 

 

Contains FCC ID: ZTL-RFSC1 

                

 

and IC: 9794A-RFSC1

This device complies with Part 15 of the 

FCC Rules. Operation is subject to the 

following two conditions:

 

(1) this device may not cause harmful 

      interference and 

(2) this device must accept any interference 

      received, including interference that may 

      cause undesired operation. 

ID: ######

Code: XXXXXX

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

•  Verify that the gateway was added successfully by checking the Gateways list. 

 

 

 
 
 

PAGE 16

PAGE 17

Ethernet Gateway MIB tree with a short description of each field:

EGW Data

Description

*GW Section

Gateway Section

*GW Serial

Gateway Serial ID

*Version

Gateway Firmware Version

*WD Count

Wireless Device Count

*WNetSection

Wireless Network Seciont

*WD Entry

Wireless Device Entry

*Index

Index Number

*Serial

Wireless Device Serial ID

*Type

Device Type (eg temp, water, motion sensor, etc)

*Age

Number of seconds since last data recording

*Active

Indicates if the wireless device is reporting in as expected

*Alarming

Indicates if the wireless device has detected data that is urgent or 

breaches a threshold

*Voltage

Battery voltage recorded at the time of data reading

*RFSignal

Signal Strength recorded on data reading delivery

*Data1

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data2

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data3

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data4

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data5

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data6

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data7

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

*Data8

Data recorded by wireless device (eg temperature, water de-

tected, motion detected, etc)

Summary of Contents for G-HUB














Reviews: