background image

F-36 PRO Laminator Operation Manual

Installation

© GBC Pro-Tech 1999 January

2-3

, +$

NOTE

ALL SHIPMENTS ARE EX- WORKS. At our dock, title 
passes to the buyer. Please review your insurance cov-
erage prior to shipment, as you are responsible for all 
subsequent freight charges and risks. Before signing 
the Bill of Lading, be sure to inspect the crate and/or 
pallet for signs of damage or missing items; if applica-
ble, make a note of this on the Bill of Lading.

The F-36 PRO Laminator is shipped one of two ways. 
It is either encased in a wood crate on a skid or in a 
cardboard box on a skid. 

 WARNING

Tools required:

Phillips head screwdriver

7

/

8

" open end wrench or adjustable wrench

If the laminator is in a cardboard box:

1. Remove the securing screws around the bottom of 

the box using the Phillips head screwdriver as 
shown in Figure 2-2.

Figure 2-2: Removing the Cardboard Box

2. Lift the cardboard box off the laminator.

3. Gently unwrap the shrink wrap from around the 

laminator.

 CAUTION

4. Carefully remove any accessories packed with the 

laminator. The accessory pack should contain:

1 Set, hex wrenches
1 Slitting knife
1 Manual
1 Set, spare fuses
1 Tape measure
1 Roll of masking tape
1 Rubber cement eraser

The unpacking process requires at least two 

people. You can be severely injured or crushed.

Do not use a knife or other sharp instrument 

during installation or while servicing the 

laminator. You can cause irreparable damage to 

the rolls.

Summary of Contents for F-36

















































Reviews: