EN
Multi Function Professional Puncher
–
B1
Changing the Settings on the LCD panel
1. Mode
With the Crease die inserted, crease function can be turned
ON/OFF. REG.ACCURACY can be turned ON/OFF and can
improve the position and reliability of the crease. However, some
decrease in system productivity may occur in this mode even if
the crease die is not inserted.
2. Backgage Depth Setting
Backgage is the distance of the punched hole(s) from the trail
edge of the sheet. This distance can be adjusted by entering the
Settings section (press Up or Down from the Home screen, and
press OK for Settings).
Pressing Up arrow will increase the Depth of Backgage, and
Pressing Down arrow will decrease the Depth of Backgage.
BACKGAGE
“-”ON THE LCD
DECREASES
BACKGAGE
DEPTH
“+”ON THE LCD
INCREASES
BACKGAGE
DEPTH
When a crease die is inserted, the Backgage Depth options are:
1 Crease Mid
CREASE LINE
“+”
ON THE LCD
“-”
ON THE LCD
MOVES THE
MOVES THE
CREASE LINE IN
CREASE LINE IN
THIS DIRECTION
THIS DIRECTION
3.
Skew Offsets (Only if Crease die is inserted)
The skew offsets can be adjusted to improve the angle of the
crease in the media.
i)
Print a 10 sheet job in
crease mode.
ii)
Measure L8 and L7 on
each sheet.
iii) Calculate L8-L7 and divide
the average of (L8-L7) by
2.
The
number
is
“X”.
iv)
Based
on
“X”
and
paper
size
on
the
table below,
search
for
input
number
“S”
to
change either BG DP L REAR or BG DP XL REAR.
v)
If L8>L7, skew offset BG DP L/ XL REAR
is
negative
“S”.
vi) If L8<L7, skew offset BG DP L/ XL REAR
is
positive
“S”.
vii)
After
inputting
“S”,
1-sheet by crease mode.
viii) After measuring L8, calculate the difference between L8 and
original paper size mid position. Input this number into
“1Crease
Mid”,
in the backgage menu to correct the crease
position.
BG DP L REAR
BG DP XL REAR
A4R
LTRR/LGL
LDR
A3
12x18
SRA3
13X19
210
216
279
297
304.8
320
330.2
X
S
0.025
1
1
0
0
0
0
0
0.05
1
1
1
1
1
1
1
0.075
2
2
1
1
1
1
1
0.1
3
3
2
2
2
2
2
0.125
3
3
2
2
2
2
2
0.15
4
4
3
3
3
3
2
0.175
5
4
3
3
3
3
3
0.2
5
5
4
4
4
3
3
0.225
6
6
4
4
4
4
4
0.25
7
6
5
5
5
4
4
0.275
7
7
5
5
5
5
5
0.3
8
8
6
6
5
5
5
0.325
8
8
6
6
6
6
5
0.35
9
9
7
6
6
6
6
0.375
10
10
7
7
7
6
6
0.4
10
10
8
7
7
7
7
0.425
11
11
8
8
8
7
7
0.45
12
11
9
8
8
8
7
0.475
12
12
9
9
9
8
8
0.5
13
13
10
9
9
9
8
0.525
14
13
10
10
9
9
9
0.55
14
14
11
10
10
9
9
0.575
15
15
11
11
10
10
10
0.6
16
15
12
11
11
10
10
0.625
16
16
12
12
11
11
10
0.65
17
17
13
12
12
11
11
0.675
18
17
13
12
12
12
11
0.7
18
18
14
13
13
12
12
0.725
19
18
14
13
13
12
12
0.75
20
19
15
14
14
13
12
0.775
20
20
15
14
14
13
13
0.8
20
16
15
14
14
13
0.825
16
15
15
14
14
0.85
17
16
15
15
14
0.875
17
16
16
15
15
0.9
18
17
16
15
15
0.925
18
17
17
16
15
0.95
19
18
17
16
16
0.975
19
18
18
17
16
1
20
18
18
17
17
1.025
20
19
18
18
17
1.05
19
19
18
17
1.075
20
19
18
18
1.1
20
20
19
18
1.125
20
19
19
1.15
20
19
1.175
20
20
1.2
20
1.225
20
PAPER FLOW DIRECTION
Skew Offset Table
8
Summary of Contents for B1
Page 2: ......
Page 93: ...RU Multi Function Professional Puncher B1 3 OK 4 5 1 2 3 Professional Puncher 93...
Page 97: ...RU Multi Function Professional Puncher B1 1 1 4 4 A 2 3 2 1 3 3 2 using 1 4 6 9 4 A 5 97...
Page 109: ...CHI Multi Function Professional Puncher B1 3 1 2 3 1 4 A 1 4 2 1 2 4 4 A 6 9 3 5 109...
