background image

Page 1-3

SPIRE II Series

 – Installation and Operating Instructions

e

lectrIcal

The laminator should be connected only to a source 
of power as indicated in these instructions and 
on the nomenclature plate located on the rear of 
the laminator. Contact an electrician should the 
attachment plug provided with the laminator not 
match the receptacles at your location. 

 WARNING: 

Do not attempt to service or repair 

the laminator. Failure to observe this warning could 
result severe personal injury or death.

Disconnect the plug from the receptacle and 
contact your dealer or distributor, or GBC Technical 
Service at 1-800-723-4000, when one or more of the 
following has occurred.

•  The power supply cord or attachment plug is 

damaged.

•  Liquid has been spilled into the laminator.
•  The laminator is malfunctioning.
•  The laminator does not operate as described 

in these instructions.

CAUTION: 

The receptacle must be located near the 

equipment and must be easily accessible. 

Disconnect the attachment plug from the receptacle 
to which it is connected and keep the power supply 
cord in your possession while moving the laminator.

GBc t

echnIcal

 s

ervIce

To order replacement accessories, service, parts, 
or an Equipment Maintenance Agreement, please 
contact GBC Technical Service and Support at:

u

nIted

 s

tates

ACCO Brands 
GBC Technical Service and Support 
4 Corporate Drive 
Lake Zurich, IL 60047 
www.gbcconnect.com

1-800-723-4000

c

anada

Ontario and Quebec – 1-800-268-3310 
All other Provinces – 1-800-268-3447 
Local 905-595-3100 
[email protected]

m

exIco

(55) 15 00 57 00

Summary of Contents for 54C













































Reviews: