background image

P.22

Preflight Setup

飛行前調整與說明

熟悉停旋練習,是提高安全的基本功,練習時請先保持直升機尾部
朝向自己及確認距離於直升機後方約5公尺並保持之。

當直升機開始離地時,慢慢降低油門使直升機降落持續
並反覆練習之以提高熟練、熟悉度。

慢慢推起油門桿
使直升機依指示移動: 向後 向前 向右 向左,
並反覆練習之以提高熟練、熟悉度。

慢慢推起油門桿
將直升機機頭移動左、右,並慢慢朝反方向移動方向舵桿
直到直升機回正於原位,並反覆練習之以提高熟練、熟悉度。

確認操控無誤並熟練後可在地上畫單一範圍限制飛行空間
,提高練習反應。

油門控制練習

Throttle Control

Keep 5 meters away behind the heli when hovering, keep 

the head toward to the front outside.

Increase the throttle little by little until the heli lifts slowly and 

decrease the throttle slowly to land it smoothly, practice it  

in both steps for a better control skill.

副翼及升降練習

Aileron and Elevator Control

Increase the throttle little by little until the heli lifts slowly and 

practice to move it to 4 directions(Forward / Backward / Left 

/ Right ), practice it in each step for a better control skill.

方向舵練習

Rudder Control

Increase the throttle little by little until the heli lifts slowly and 

practice to move the head to Left or Right side, practice it in 

each step for a better control skill.

Practice to Control the heli in a specific area to get 

the quick response about it.

Mode 1

Mode 2

Mode 2

Mode 1

2

3

4

1

Mode 1

Mode 2

2

2

3

3

4

4

1

1

Summary of Contents for Hurricane 255





























Reviews: