background image

© 2016 Hobbico

®

, Inc.  All rights reserved.

FLZA4120

Length:

38.5 in
[980mm]

Radio:

5-channel
radio system

Motor:

40mm dia.
850kV outrunner,
40A ESC,
12x6 propeller

SPECIFICATIONS

Wingspan:

59.5 in
[1510mm]

Wing

Area:

430 in

2

[27.7 dm

2

]

Weight:

3– 3.25 lb
[1360–1470 g]

Wing

Loading:

16–17 oz/ft

2

[49– 52 g/dm

2

]

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Flyzone guarantees this kit to be free from defects in both 
material and workmanship at the date of purchase. This 
warranty does not cover any component parts damaged by use 
or modification. In no case shall Flyzone’s liability exceed the 
original cost of the purchased kit. Further, Flyzone reserves the 
right to change or modify this warranty without notice.

In that Flyzone has no control over the final assembly or material 
used for final assembly, no liability shall be assumed nor 
accepted for any damage resulting from the use by the user of 
the final user-assembled product. By the act of using the 
user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with 
the use of this product, the buyer is advised to return this kit 

immediately in new and unused condition to the place of 
purchase.

To make a warranty claim send the defective part or item to 
Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr.  Suite 1

Champaign IL  61822  USA

Include a letter stating your name, return shipping address, as 
much contact information as possible (daytime telephone 
number, fax number, e-mail address), a detailed description of 
the problem and a photocopy of the purchase receipt. Upon 
receipt of the package the problem will be evaluated as quickly 
as possible.

INSTRUCTION MANUAL

Island Wings Select

Summary of Contents for DHC-2 BEAVER





















Reviews: