Gateway 930 series System Manual Download

Page: 80 / 160

Replacing and Adding System Components

Replacing the back panel and drive
cage fans

The back panel fan is located below the power supply on the back panel. The
drive cage fan is located behind the hot-plug cage, between the hot-plug cage
and the system board. See the illustration on page 6 for more information.

To remove the back panel or hot-plug cage fan:

Turn off the system and disconnect the power cord, modem cord (if
installed), and all external peripheral devices.

Observe all safety and static electricity precautions. (See “Preventing static
electricity discharge” on page 22.)

Remove the bezel. (See “Removing the bezel” on page 25.)

Remove the left side cover panel. (See “Removing the side cover panel”
on page 26.)

Press the two locking tabs on the fan bracket, then disengage the two
retaining tabs from either the back panel or the hot-plug cage.

8508088.book Page 72 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands