Gateway 930 series System Manual Download

Page: 33 / 160

Opening the case

Removing the bezel

The locking bezel provides secure access to the system components. You must
unlock and remove the bezel before you can remove the side cover panel and
access the interior of the system.

To remove the bezel:

Turn off the system and disconnect the power cord, modem cord (if
installed), and all external peripheral devices.

Observe all safety and static electricity precautions, see “Preventing static
electricity discharge” on page 22.

Remove the bezel by pressing the tabs at the sides of the bezel and pulling
the top of the bezel away from the server.

Lift the bezel away from the chassis.

8508088.book Page 25 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands