Gateway 930 series System Manual Download

Page: 14 / 160

System Features

Interior of server

Power supply

provides power to the system components. The redundant

power supply provides hot-plug capability and fault tolerance.

Power supply fans

provide cooling for the redundant power supply modules.

5.25-inch drive bays

provide space for as many as four 5.25-inch drives. A

CD drive comes standard with the system and occupies one of the 5.25-inch
drive bays.

3.25-inch drive bays

support as many as two 3.25-inch drives. A diskette drive

comes standard with the system and occupies one 3.25-inch drive bay. A hard
drive is typically installed in the second drive bay.

Hot-plug bays

support as many as six 1-inch high 3.25-inch SCA SCSI hard

drives. Empty drive bays contain empty drive carriers to control airflow and
EMC emissions.

SCSI backplane

provides the control for the hot-plug drives.

Power supply

Power supply fans

5.25-inch
drive bays

Back
panel fan

System
board

System
board tray

Hot-plug
cage fan

SCSI
backplane

3.25-inch
drive bays

Hot-plug bays
(Hot-plug cage)

8508088.book Page 6 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands