background image

1

2

Danger

■ Please read this precautions carefully. And Keep this manual  

  safe for future reference.

■ These precautions are written to defend the user to keep    

  other people from harm, and to prevent other damages.    

  Please pay attention to these precautions. 

■ These signs indicate the level of danger which can be      

  expected by improper use.   

 

 

1. 

Precautions

Imminently dangerous 
situation, such as death 
or severe injury

Warning

Can cause break down, 
injury, and electric 
shock

Caution

Caution

Injury or physical 
damages

Things the user must NOT do.

Things the user must do.

Avoid keeping at the place 
where much humidity, dust and 
high temperature are present.

● Can cause the break down 

 

Do not leave or use this 
sensor in the direct sunlight 
or high temperature place.

Do not put on an unstable 
place like a sloping table.

● Can cause injury or breakdown

Please measure the tensile 

force after confirming the 

machine has been turned off.

Do not make strong impact or 
throw.

● Can cause breakdown and fire

Do not use this in a 
flammable environment. 

 

 

● Can cause an explosion or the fire  

  when using this near propane gas 

  or gasoline 

Do not break down or 

change.

● Can cause injury

Even though the arm parts of 
the sensor are flexible, do not 
bend at an acute angle. Please 
do not bend it close to the 
head of the sensor (within 
20mm from the sensor), and 
also do not bend it at the 
bottom of the sensor. Do not 
grab or twirl the cord strongly.

Please turn off the power, 

immediately right after you 

hear a thunder noise and 

move to a safety place. 

 

 

 

 

 

● Can cause an electric shock

Do not put liquids such as 
water or solvents on the 
meter. Do not use the sensor 
in a wet or oily environment.

Do not use solvents (thinner 
and benzene, etc.) for 
maintenance.

Warning

u550_e_manual.indd   4

2020/12/08   16:18

Summary of Contents for U-550

















Reviews: