background image

[Figure 2. GTD-3000ExW Components]

www.gastron.com

08

_

09

4. Name and Description of Each Part

4.1. Components

3.3. Electrical Specifications (Standard Type)

ITEMS

SPECIFICATION

Input Voltage(Standard)

※ Customer supplied PSU must meet

requirements IEC1010-1 and CE

Marking requirements.

Absolute min:

Nominal:

Absolute max:

Ripple maximum allowed:

18V
24V
31V

1V pk-pk

Wattage

Max. wattage:

Max. current:

5.5W @+24 VDC

280mA @+24 VDC

Analog output Current

0-20mA(500 ohms max load) 

All readings ± 0.2mA

Measured-value signal: 

4mA(Zero) to 20mA(Full Scale)

Fault:

0-100% LEL:

100-109%LEL: 

Over 110% LEL: 

Maintenance: 

0mA

4mA - 20mA

20mA - 21.4mA

22mA

3mA

Analog output current ripple & noise max

±20uA

Relay contact

Alarm1, Alarm2, Fault Relay

Rated 1.0 A @ 30VDC or 0.5 A @ 125 VAC

Wiring requirement

Power

CVVS or CVVSB with shield

Analog

CVVS or CVVSB with shield

RS485

STP(Shielded Twisted Pair)

Cable Connection Length

Analog

2500m

RS485

1000m

EMC Protection:

Complies with EN50270

NO

NAME

DESCRIPTIONS

1

Housing

Protects Sensor and PCB Board built in the Housing from external environmental change and shock.

2

Main PCB

It amplifies output signal from the sensor and converts and send it as DC 4~20 mA standard output. 

Isolation RS-485 network and alarm relay contact signals are outputted. Also, it sends data for the display.

3

Display PCB

It displays data received from main PCB on LCD or OLED and displays the current event status with 

power lamp, alarm lamp, trouble lamp.

4

Power/Signal Terminal

CN1 consists DC18-24 V power supply and DC 4~20 mA standard output connection terminal (VISO, 

+24V, mA,-, ETH).

5

Alarm signal Terminal

CN10 is alarm signal connection terminal, which outputs trouble, alarm1, alarm2 relay contacts.

3.4. Environmental Specifications

ITEMS

SPECIFICATION

Operation Temperature

Transmitter

-20 to 60 ℃

Sensor

Refer to Sensor Specification

Storage Temperature

Transmitter

-20 to 60 ℃

Sensor

Refer to Sensor Specification

Operation Humidity

Transmitter

5 to 99% RH (Non-condensing)

Sensor

Refer to Sensor Specification

Pressure Range

90 to 110KPa

Max. air velocity

6m/s

3. Specification

GTD-3000ExW

Instruction Manual

Summary of Contents for GTD-3000ExW



















Reviews: