Start Up
If motor fails to start or slows down significantly under
load, shut off and disconnect from power supply. Check
that the voltage is correct for motor and that motor is
turning in the proper direction. Vane life will be drastical-
ly reduced if motor is not operating properly. Vanes can
break or be damaged if motor/pump runs in the wrong
direction.
OPERATION
Use only recommended air handling parts
acceptable for pressure not less than 70 psi..
Keep fingers and objects away from openings and
rotating parts.
When provided, motor terminal covers must be in
place for safe operation.
Check that coupling guard and shroud are in place
before operating.
Product surfaces may become hot during operation,
allow product surfaces to cool before handling.
Do Not direct air stream at body. Air stream from
product may contain solid or liquid material that can
result in eye or skin damage, wear proper eye
protection.
Do Not spray flammable or combustible liquid.
Wear hearing protection. Sound level from product
may exceed 85 dBA.
Failure to follow these instructions can result in
burns, eye injury or other serious injury.
WARNING
Injury Hazard
Install proper safety guards as needed. Pumps with
glass jars need safety guards to protect against
breaking glass.
Check with a qualified electrician or serviceman if the
grounding instructions are not completely understood,
or if you are not sure whether the product is properly
grounded. Do not modify the plug provided. If it will not
fit the outlet, have the proper outlet installed by a quali-
fied electrician.
Model that is permanently wired:
This product must be connected to a grounded, metal-
lic, permanent wiring system, or an equipment ground-
ing terminal or lead on the product.
Power supply wiring must conform to all required safety
codes and be installed by a qualified person. Check
that supply voltage agrees with that listed on product
nameplate.
Be sure the 3-phase motor turns in the proper direction
of rotation after installation. Turning in the wrong direc-
tion will drastically reduce vane life.
Extension cords:
Use only a 3-wire extension cord that has a 3-blade
grounding plug. Connect extension cord plug to a
matching 3-slot receptacle. Do not use an adapter.
Make sure your extension cord is in good condition.
Check that the gage wire of the extension cord is the
correct size wire to carry the current this product will
draw.
Minimum gage for extension cords
Amps
Volts
Length of cord in feet
120v
25 50
100 150 200 250 300 400 500
240v
50 100 200 300 400 500 600 800 1000
0-2
18 18
18
16
16
14
14
12
12
2-3
18 18
16
14
14
12
12
10
10
3-4
18 18
16
14
12
12
10
10
8
4-5
18 18
14
12
12
10
10
8
8
5-6
18 16
14
12
10
10
8
8
8
6-8
18 16
12
10
10
8
6
6
6
8-10
18 14
12
10
8
8
6
6
4
10-12
16 14
10
8
8
6
6
4
4
12-14
16 12
10
8
6
6
6
4
2
14-16
16 12
10
8
6
6
4
4
2
16-18
14 12
8
8
6
4
4
2
2
18-20
14 12
8
6
6
4
4
2
2
It is your responsibility to operate this product at recom-
mended pressures or vacuum duties and room ambient
temperatures. Do Not start against a vacuum or pres-
sure load.
Model with a power supply cord:
This product must be grounded. For either 120-volt or
220/240-volt circuits connect power supply cord ground-
ing plug to a matching grounded outlet. Do not use an
adapter. (See DIAGRAM A)
In the event of an electrical short circuit, grounding
reduces the risk of electric shock by providing an escape
wire for the electric current. This product may be
equipped with a power supply cord having a grounding
wire with an appropriate grounding plug.
The plug must be plugged into an outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
3
