background image

                                                                    User Manual 

X45 

Version 1.0/2019

 

 
  

           

   

Copyright © 2019 by Xicoy Electrònica S.L. All rights reserved

             

Page

   

4

 

If you sell or pass on this engine to a 2

nd

 or subsequent owner please also pass on this User’s Manual or its link, so they 

can enjoy a safe and fulfilling ownership too.

 

The  Xicoy  Electronica  SL responsibility  is  limited  exclusively to the repair  of  the engine  and  accessories which  are 
outlined in the conditions of warranty.

 

Before unpacking the engine, please read through these notes and agree to the conditions of warranty.

 

Customer  satisfaction  is  important  to  Xicoy  Electronica.  Technical  support  is  readily  available  through  your  local 
dealer and via email:

 

Xicoy Electronica SL, Plaça Pere Llauger Nau 18, 08360, Canet de Mar, Barcelona, Spain

 

Web site: 

www.xicoy.com

 Email: 

[email protected]

 

See our new turbine webpage at: 

www.Xicoyturbines.com

 

 

Legal  

The  engine  design  and  contents  of  this  User  Manual  are  copyright  Xicoy  Electronica  SL,  Canet  de  Mar,  Barcelona, 
Spain. All rights are reserved.

 

This User manual, pictures and data are the property of Xicoy Electronica SL and cannot be used or reproduced in any 
way with written permission from Xicoy Electronica SL.

 

 

Disclaimer 

This X45 engine is a very sophisticated piece of machinery. Great care should be taken at all times when using the 
engine. It should only be operated by those with appropriate skills and knowledge to do so. The engine is not a toy. 
Incorrect operation or misuse can cause damage to property and bodily harm to operators, spectators or animals. 
Xicoy Electronica SL accepts no liability any damage which may occur.

 

Xicoy  Electronica  SL  assumes  no responsibility  for any  errors contained  in  this document  and is  not  liable  for  any 
damages resulting from such errors.

 

It is forbidden to use this engine outside radio control applications, especially those that power vehicles to carry 
people. 

 

Summary of Contents for Xicoy X45




























Reviews: