background image

9

8

8

TEST FIRING APPLIANCE

Test fire appliance, following the lighting instructions 
found on the appliance. Leak test all gas connections 
with soapy water. Soap bubbles indicate gas leakage. 
DO NOT use a flame to test for gas leaks.

WARNING: White smoke may appear 
around the burner during the first minute of 
the initial firing.

9.  In the event that the flame goes out (due to wind 

or other reasons) the flame failure device will 
automatically shut off the gas supply after 60 
seconds. To re-light start lighting process from Step 1.

10. To turn ‘OFF’ the appliance turn control knob to the 

‘OFF’ position.

11. Open LPG compartment panel and turn the LPG 

cylinder valve to ‘OFF’ position.

12. Allow the appliance to cool before moving and 

covering for storage (at least 30 minutes).

Note: If for some reason, igniter fails to produce a spark 
at the electrode, fire bowl can be lit by a long match. 
Move glass beads to gain access to the burner (DO NOT 
touch unless completely cool). Wearing heat resistant 
gloves, position long lit match close to burner port. DO 
NOT lean over burner while lighting.
Push and turn burner control knob to “LOW” position. 
The burner should light within 5 seconds.

STORAGE & MAINTENANCE

To obtain the best performance from your fire table, you 
must perform the following storage and maintenance 
activities on a regular basis:

•  Allow at least 30 minutes for the fire table to cool 

down after use, then disconnect and remove the 
cylinder.

•  Store the gas cylinder in a dry, well ventilated and 

sheltered area away from weather and dust, out of the 
reach of children, and not in a building, garage or any 
other enclosed area.

•  Storage indoors is permissible only if the cylinder is 

disconnected and removed. It is recommended that 
the fire table be stored indoors during the winter if it 
will be subjected to freezing temperatures.

•  Keep the fire table area clear and free from 

combustible materials, gasoline and other flammable 
vapors and liquids.

•  If the fire table is not in use, it must be covered to 

protect from weather or other adverse elements.

•  Never use a vacuum cleaner on the glass beads.
•  Installation and repair should be done by a qualified 

service person.

•  The fire table should be inspected at least annually 

by a qualified service person. It is imperative that 
control compartment, burners and circulating air 
passageways of the fire table be kept clean.

TEST FIRING APPLIANCE

For first time use and after every change of LPG cylinder 
the gas system must be purged of air before lighting. To 
do this, turn your LPG cylinder valve on and push in and 
turn the control knob to ‘HIGH’ position. Hold in control 
knob for 1 minute before attempting to light appliance.

1.  Make sure that the control knob is in the ‘OFF’ position.
2.  Remove LPG compartment panel to gain access to 

LPG cylinder. Turn cylinder valve to ‘ON’ position and 
replace panel.

3.  Push in the control knob and keep depressed while 

turning to the ignition point marked with a ‘ ’ or 
‘LOW’. Once the control knob is at this point push the 
ignition button. The Igniter will spark automatically, if 
it does not spark, release control knob and return to 
the ‘OFF’ position. Then check if battery is inserted 
correctly or if the ignition wire has come loose under 
the burner.

4.  When the burner is lit and flames are visible in the 

‘LOW’ position release ignition button but keep the 
control knob depressed for a further 20 seconds and 
then release it.

5.  If the burner does not stay 

lit, turn off control knob and 
the cylinder valve and wait 
5 minutes and repeat from 
Step 1.

6.  Burner is now lit in the 

‘LOW’ position.

7.  Adjust the flame and heat 

output by turning the control 
knob from ‘LOW’ to ‘HIGH’ 
a few times to check the 
flame stability.

8.  Adjust control knob to desired output between ‘LOW’ 

and ‘HIGH’.

IMPORTANT: Cover must be removed 
when burner is in operation.

Summary of Contents for URBO GM142-163













Reviews: