background image

7

6

ASSEMBLY INSTRUCTIONS

STEP 5b
Tighten the connections using a crescent then 
repeat steps 3-4.

STEP 5b
The connection is gas tight when no bubbles grow 
around the gas connection.

STEP 6
The ignition system works by battery. Unscrew 
the electronic igniter button and insert the AAA 
battery included. Make sure the positive pole (+) is 
towards the outside. Re-screw the button back to 
the battery case tightly.

STEP 7
Place all glass beads evenly in the fire table on 
the top of the appliance. Never cover the ignition 
screen when placing the glass beads into the fire 
table. Always keep ignition screen visible.
Note: Images are examples only. Burner shape 
may differ from the images below.

WARNING: This screen must be clear and 
free of obstructions at all times to ensure 
proper operation.

STEP 8 - Glass Assembly:

1. Locate brackets and the screw and silicon pad 

bag.

2. Place an L silicon pad (D) at the bottom of each 

bracket (B) and then arrange the brackets on 
the fire table top surrounding the burner. This 
will protect the table top finish.

3. Remove the glass panels (A) from the 

packaging. Place a square shaped silicon pad 
(E) on each side and corner of the glass. Insert 
the glass panel into the bracket. Tighten the 
screw (C) to secure the glass to the bracket. 
Be careful when tightening the screws not to 
damage the glass. Complete this on all four 
corners.

4. Ensure that the glass is centred on the table 

top.

STEP 11

Ensure cylinder valve is in its full off position. Check 
for any damage to either the cylinder connection or 
the hose. NEVER attempt to use damaged equipment. 
Attach the regulator and hose to your gas cylinder. 
Tighten the nut to a positive stop by hand.

STEP 12

Turn on the gas cylinder ensuring that the control knob 
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.

STEP 13

Use a solution of soapy water (dishwashing liquid and 
water is fine). Brush it on or use a spray bottle as 
shown in the drawing. Ensure the connections have a 
good coating.

STEP 14a

If the connection is leaking, bubbles will start to grow 
in the soapy solution. If this happens shut off the gas 
supply at the cylinder. 

STEP 14b

Tighten the connections using a crescent then repeat 
steps 12-13.  

STEP 14c

The connection is gas tight when no bubbles grow 
around the gas connection.

ASSEMBLY INSTRUCTIONS

STEP 11

Ensure cylinder valve is in its full off position. Check 
for any damage to either the cylinder connection or 
the hose. NEVER attempt to use damaged equipment. 
Attach the regulator and hose to your gas cylinder. 
Tighten the nut to a positive stop by hand.

STEP 12

Turn on the gas cylinder ensuring that the control knob 
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.

STEP 13

Use a solution of soapy water (dishwashing liquid and 
water is fine). Brush it on or use a spray bottle as 
shown in the drawing. Ensure the connections have a 
good coating.

STEP 14a

If the connection is leaking, bubbles will start to grow 
in the soapy solution. If this happens shut off the gas 
supply at the cylinder. 

STEP 14b

Tighten the connections using a crescent then repeat 
steps 12-13.  

STEP 14c

The connection is gas tight when no bubbles grow 
around the gas connection.

ASSEMBLY INSTRUCTIONS

Correct

Incorrect

Screen

DO NOT 
place glass 
beads on the 
screen. Keep 
screen clear.

Summary of Contents for URBO GM142-163













Reviews: