Gasmate Odyssey BQ1060MG Manual Download Page 14

15

14

CARE & MAINTENANCE

As with all appliances, proper care and maintenance 
will keep them in top operating condition and prolong 
their life. Your new gas barbecue is no exception. By 
following these cleaning procedures on a timely basis, 
your barbecue will be kept clean and working properly 
with minimum effort.
Spiders and small insects occasionally spin webs or 
make nests in the burner tubes during warehousing and 
transit.
These webs can lead to a gas flow obstruction which 
could result in a fire in and around the burner tubes.  
Cleaning with a soft brush before use and at least every 
six months is recommended.
This type of fire is known as ‘FLASH-BACK’ and can 
cause serious damage to your barbecue and create an 
unsafe operating condition for the user. Although an 
obstructed burner tube is not the only cause of ‘FLASH-
BACK’ it is the most common cause and frequent 
inspection and cleaning of the burner tubes is necessary.

Flash-Back

If fire occurs in and around the burner, immediately turn 
off gas at its source and turn the burner control to ‘OFF’, 
wait until the barbecue has cooled, then clean the burner 
tubes and burner ports.

Cleaning the Cooking Surface

After cooking, turn burner control to ‘OFF’ and let 
barbecue cool before attempting to clean the grill plate 
or grate. Before first use and periodically, it is suggested 
that you wash the grill plate and grate in a mild soap and 
warm water solution.

Care of Cooking Surface

Use and care of the cooking surface is important. Do not 
use pans on the cooking surface. Do not overheat the 
cooking surface with the hood down or no food on the 
cooking surface.

Cleaning the Drip Tray

To avoid fat or grease dripping from the barbecue remove 
and empty the drip tray after each use. Wait until the drip 
tray is cool to touch before disposing of contents.
The drip tray should be washed periodically in a mild 
detergent and warm water solution.   

 IMPORTANT

•  Beware of spiders and wasps. Burner tube 

should be inspected and cleaned periodically.

•  This appliance must only be serviced by an 

authorised person. 

•  To avoid any flare-ups, it is recommended that 

the drip tray be checked and emptied regularly. 
Contents of the drip tray may be very hot during 
cooking. If emptied during extended cooking 
extreme caution should be taken and direct 
contact by hand should be avoided at all times. 
Allow to cool completely before disposing of the 
contents.

Summary of Contents for Odyssey BQ1060MG

















Reviews: