background image

5

4

Location of your Barbecue

DO NOT use your barbecue in garages, porches, sheds, 
breezeways, or other enclosed areas. Your barbecue is to 
be used OUTDOORS. The barbecue is not intended to be 
installed in or on recreational vehicles and/or boats and 
should not be placed under any surface that will burn. Do 
not obstruct the flow of combustion and ventilation air 
around the barbecue housing.

Protect Children

Keep children away from barbecue during use and until 
barbecue has cooled after you have finished. Do not 
allow children to operate barbecue.
Always ensure that no sporting or physical activities are 
carried out in close proximity to the barbecue during use 
and while still hot.

Tools You Will Need

Adjustable spanner, Phillips head screwdriver.

Check Barbecue for any Damage

Inspect barbecue parts as you proceed. Contact your 
supplier for assistance regarding replacement of any 
damaged or missing parts. Do not assemble or operate a 
barbecue that appears damaged. Barbecues for use with 
gas cylinders are labelled ‘ULPG’. Check labelling at the 
gas connection on your barbecue.

Nominal Hourly Gas Consumption

Left  
Burner

Centre  
Burner

Right  
Burner

Gas Type

U.L.P.G

U.L.P.G

U.L.P.G

Inj. Size

0.92mm

0.92 mm

0.92mm

Gas Cons.

11.0 MJ/h

10.5 MJ/h

11.0 MJ/h

Gas Pressure

2.75 kPa

2.75 kPa

2.75 kPa

For warranty details visit www.gasmate.co.nz

For warranty claims, return to the place of purchase. Keep your purchase receipt, this will be required 

to make any claims under the 12 month warranty.

Summary of Contents for Odyssey 3T





















Reviews: