background image

10

The following figures are diagrammatical representations of outdoor areas.  Rectangular areas have been 
used in these figures - the same principles apply to any other shaped area.

SAFE APPLIANcE LOcATIONS

This appliance shall only be used in an above ground open-air situation with natural ventilation, without 
stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and 
natural convection.

Any enclosure in which the appliance is used shall comply with one of the following:

 An enclosure with walls on all sides, but at least one permanent opening at ground level and no 
overhead cover (see Example 1).
Within a partial enclosure that includes an overhead cover and no more than two walls (see Example 2 
& 3).

Within a partial enclosure that includes an overhead cover and more than two walls, the 

following will apply:

at least 25% of the total wall area is completely open, and

at least 30% of the remaining wall area is open and unrestricted (see Example 4 & 5).
In the case of balconies, at least 20% of the total wall area shall be and remain open and unrestricted.

Gasmate

®

 is a registered trademark of:     Sitro Group Australia Pty Ltd   www.gasmate.com.au 

 

 

             Aber, Hamilton, N.Z   www.gasmate.co.nz

Summary of Contents for Inferno FHIN100 Series











Reviews: