background image

TXT Pro 2004 -

28

-

Warranty regulations

Manufacturer’s warranty

The Company GAS GAS Motos S.A. hereby warrants to the final purchaser of a vehicle manufactured by GG that both materials and

workmanship are free from defects according to the corresponding state of the art. Accordingly, GG hereby warrants to the final purchaser

 (hereinafter referred to as the “purchaser”), subject to the conditions stated below, to remove any defects in material or production

detected in a new motorcycle free of charge within the agreed period of warranty without any limitation whatsoever in terms of the

number of kilometres travelled or the number of operating hours.

Period of warranty

The period of warranty shall commence on the day of delivery of the vehicle by a licensed GG dealer to the purchaser, or in the case

of demonstration models, on the date on which the vehicle is put into operation for the first time.

 The length of the warranty period depends on the type of vehicle and is stated in the document of delivery.

Any defects detected in the product shall be brought to the attention of a licensed GG dealer within the warranty period. If the last

day of the warranty period is a Sunday or public holiday, the warranty period shall be extended in such a way that the last day of the

warranty period is the next working day following the respective Sunday or public holiday. Warranty claims shall be excluded for any

defects not brought to the attention of a licensed GG dealer by the end of the warranty period.

obligation of the purchaser

GG shall be entitled to refuse to accept warranty claims if and to the extent that:

a) the purchaser has failed to subject the vehicle to any of the inspections and/or maintenance work prescribed in the operating manual

or has exceeded the date stated for such inspections or maintenance work, also excluding from the warranty defects that appeared before

the prescribed date of such inspection or maintenance work performed not at all or performed only after the prescribed date;

b) inspection, maintenance work and repair work on the vehicle has been performed by a party neither recognized nor licensed by GG;

c) any maintenance or repair work has been performed on the vehicle in violation of the technical requirements, specifications and

instructions indicated by the manufacturer;

Summary of Contents for TXT PRO - 2004
































Reviews: