background image

Multi Gas Clip Simple Plus User’s Manual

UM MGC-S-PLUS v1.00a 

Portable gas detectors you can count on

17 of 18

Size

4.75 H x 2.75 W x 1.25 D in. (120.65 x 69.85 x 31.75 mm.)

Weight

7.675 oz. (220.2 g) 

Temperature

-4˚F to +122˚F (-20˚C to +50˚C)

Humidity

5% to 95% RH (non-condensing) 

Battery Life

1095 days continuous 

based on an average of 1 minute/day of alarm condition 

Alarms

Visual, Vibrating, Audible (minimum 95dB)

Low, High, STEL, TWA and OL (Over Limit) 

LEDs

4 Red alarm bar LEDs 

Yellow backlight (activated on button press)

Red backlight (activated on alarm condition)

Yellow Maintenance Notification LED 

Display

Alphanumeric Liquid Crystal Display (LCD) 

Logs

50 Bump Tests 

50 Events 

50 Calibrations 

Continuous 1-second data logging (typical capacity > 2 months) 

Tests

Full function self-test upon activation 

Sensors, battery and circuitry tests run continuously 

Ingress Protection

IP 68

Warranty

Full 3 years

Gases

Gas

Range

Resolution

Accuracy*

T

90

*

H

2

S

0 – 100 ppm

0.1

<2 ppm

<30s

CO

0 – 500 ppm

1

<5 ppm

<30s

Combustible

0 – 100% LEL

0.1

See Table 1, page 18

<30s

O

2

0 – 30% vol.

0.1

<0.7% vol.

<15s

Sensor Type

H2S, CO, O2: Single plug-in electrochemical cell

Combustible (LEL): Soldered infrared (IR)

User Options

User Message, Language, Low Alarm, High Alarm, STEL Alarm, TWA Alarm, TWA Method, TWA Interval, STEL 

Interval, SAFE, Maintenance Notification, Self-test Lock,  Dock Lock, Sensor Enable/Disable, Calibration 

Interval, Bump Interval, Calibration Gas, %-by-volume, Latching Alarms, Life Display and Off Lock

Approvals

CSA:                  

Class I, Division 1, Group A, B, C, and D

                           Class I, Zone 0, A/Ex ia IIC T4 Ga

                           C22.2 No. 152-M1984 

                           ANSI/ISA S12.13

ATEX:

              SIRA 16ATEX2288

                           CE 0518 

 II 1 G Ex ia IIC T4 Ga

                           (-20°C  ≤ Ta ≤ +50°C)

                           EN 60079-0:2012/A11:2013

                           EN 60079-11:2012

IECEx:               

CSA 16.0038

                           Ex ia IIC T4 Ga

                           IEC 60079-0:2011

                           IEC 60079-11:2011 

DETECTOR SPECIFICATIONS

*Sensor performance is dependent on many factors, including temperature, humidity, sensor age, filter cleanliness, gas 
delivery, and calibration accuracy. Typical performance will be better than the given limits under most circumstances.

Summary of Contents for Multi Gas Clip Simple Plus





















Reviews: